Advertisement
Quick Links
Advertisement
Related Manuals for LG PL-F860
Summary of Contents for LG PL-F860
- Page 1 User Manual Quad Digital Pillar Please read the Safety Precautions carefully before using this product. After reading this manual, please keep it in an easily accessible location for future reference. PL-F860 www.lg.com *MFL69559203* P/No: MFL69559203 (1607-REV00) Printed in Korea...
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS Please read this manual carefully to properly install this product. After reading the manual, please keep it in an easily accessible location for future reference. WARNING • Carefully follow the instructions in this manual to install this product correctly. - Failure to follow the instructions in the manual can result in personal injury or product damage. -
Page 3: Assembly And Preparation
If the instructions in the manual are unclear, stop the installation process and contact the service center. • Check that the accessories provided with the product are all included before beginning installation. LG Electronics is not liable for any damage or loss of accessories after the package has been opened. - Page 4 Accessories Accessories are subject to change without prior notice to improve the performance of the product, and new accessories may be added as well. The illustrations in this manual may differ from the actual product and accessories. Bracket (8 EA) Bracket screw Top cover screw Mount base (16 EA)
- Page 5 Assembly The images may differ from the actual product. WARNING • For safety, at least two people must work together to install the product. • Make sure to use gloves or other protective equipment during assembly for safety. Place the stand base on a flat surface. Place the pillar on the stand base, aligning it with the grooves in the base.
- Page 6 Place the pillar on the grooves on the stand base and assemble using the eight screws (M8 x L50) provided. Put a power strip into the hole in the stand base. The shape of the power strip may differ by region. SCALE 3/2 SCALE 3/2...
- Page 7 Apply the double-sided tape to the power strip and attach it to the inner side of a pillar as shown in the image. NOTE • Cut the double-sided tape in sizes that will fit the size of the power strip. •...
- Page 8 If using a media player provided by LG Electronics, place it inside the media player box attached to the pillar. Media player box...
- Page 9 If using a media player other than those provided by LG Electronics, loosen the screws to remove the media player box and attach using a different bracket.
- Page 10 Lay a clean cloth on the floor, and then put the monitor set on it with the screen face down. Place the brackets on the back of the monitor set, aligning them with the VESA holes. VESA hole Use the four screws (M8 x L10) provided and an L-wrench to attach the brackets to the monitor set. Make sure the holes in the brackets and the VESA holes are aligned.
- Page 11 Place a soft cushion next to the pillar attached to the stand base. (Cushion size: At least 100 mm x 400 mm) Hold the assembled brackets and use the cushion to set the monitor set upright.
- Page 12 Refer to the image below and make sure one person is holding the top of the monitor set while the other is holding the bottom panel, then lift it up. Use the brackets to hang the monitor set on the pillar. WARNING •...
- Page 13 After hanging the monitor set on the pillar, connect the power cord and IR receiver. Attach the IR receiver to the bottom of the monitor set. IR receiver Hang two more monitor sets on the pillar in the same method. The last monitor set must be hung on the pillar after the power cord and IR receiver are connected.
- Page 14 Assemble the provided screws (M4 x L20) and mount bases. Tighten two screws and mount bases each in the holes in the sides of the monitor sets.
- Page 15 Make sure the holes in the deco frame are slightly higher than the monitor set's screws. Hang the screws attached to the monitor sets onto the deco frame.
- Page 16 Push down on the deco frame so it is attach in place.
- Page 17 Attach the top cover using the guides as shown in the image, and attach with the eight screws (M4xL10) provided.
-
Page 18: Product Specifications
PRODUCT SPECIFICATIONS Model name PL-F860 Width (mm) Height (mm) 2,291.2 Depth (mm) Product weight (kg) 132.5 Product weight in package (kg) - Page 20 The model name and serial number can be found on the Contact your retailer for the applicable model. back of the product. Please make a note of the following: Model name Serial No.