Summary of Contents for Dynamco CYCLOPS PARALYSER 485
- Page 1 PARAL YSER 485 USER INSTRUCTIONS CYCL PS SECURITY SYSTEMS PROUDLY AUSTRALIAN Proudly designed and engineered in Australia by...
- Page 2 Dynamco Pty Ltd. Your emergency override PIN is Keep this number in a safe place for future reference (DO NOT keep it in the vehicle). Ensure this page is completed by the installer at time of purchase. - Page 2 -...
- Page 3 Australian designed and engineered vehicle security systems, installed in your vehicle! The Cyclops Paralyser 485 has been tested to and meets Australian Standards AS/NZS 3749.1.1997 & AS/NZS 3749.1:2003. Ensure the warranty details on the back page is completed by your installer.
-
Page 4: Arming And Disarming
ARMING AND DISARMING To arm the P485, press the lock button on the remote control supplied by the vehicle manufacturer. Arming the system is accompanied by two flashes from the indicators and two chirps from the siren. The status LED (red light on the dash) will glow, then begin flashing after 5 seconds. -
Page 5: Programmable Options
ENGINE IMMOBILISATION Engine immobilisation is usually provided by the vehicle's original equipment system. The P485 does provide another two independent circuits of immobilisation, however they are only connected at special request (extra cost). GLASS BREAKAGE PROTECTION The P485 is equipped with a sophisticated glass breakage detection unit. The system will only respond to the breaking of glass in the vehicle (sound can be muffled by heavy window tinting). - Page 6 PROGRAMMABLE OPTIONS cont’ TURNS DESCRIPTION 1 FLASH RESPONSE 3 FLASHES RESPONSE Siren chirp order Reversed Standard Immobilisation dropout time* When armed After 30 seconds Arm/disarm flash confirmation** Enabled Disabled Siren/horn output type Pulsed for 30 sec Constant for 30 sec Arm/disarm confirmation Disabled Enabled...
-
Page 7: Changing Pin
OVER-RIDE cont’ PIN Code If the P485 is triggered, allow siren to reset automatically (after 30 seconds) by sitting inside car with doors shut. If the siren is switched off, wait for indicators to stop flashing. Turn the ignition switch to the “ON” position; the status LED will glow constantly. Turn ignition switch back to the “ACC”... -
Page 8: Problem Solving
DIAGNOSTICS For your convenience and peace of mind the P485 features a user friendly diagnostic facility, that reports the source of the last trigger. The report is produced by disarming the P485 during or after a siren trigger. The report consists of the normal indicator disarm flash, followed by 1, 2, 3 or 4 flashes. -
Page 9: Annual Inspection
ANNUAL INSPECTION Dynamco prides itself on the durability and integrity of its car security systems. We welcome users to contact your installer every twelve months for an annual inspection. (Please note a charge may be levied for this inspection) 1st Inspection... - Page 10 The product has been repaired by any other person other than by an authorised Cyclops service centre. Should a defect become apparent within the warranty period Dynamco Pty Ltd will repair the product free of charge for parts and labour. Should a mobile service be required, a call-out charge may apply.
-
Page 11: Optional Accessories
OPTIONAL ACCESSORIES The P485 has special inputs and outputs to interface with many optional accessories, please consult your installer before installation is complete (additional cost may apply). These accessories include: Electric Window Closer When the P485 is armed, a command is sent to a module (WIN- 004) that will power electric windows until each inturn is fully closed. -
Page 12: Warranty Registration
WARRANTY REGISTRATION CYCL PS SECURITY SYSTEMS PURCHASED FROM OWNER’S NAME TYPE OF VEHICLE VEHICLE REGO MODEL OF UNIT DATE OF INSTAL’ WARRANTY PERIOD : CONTROL MODULE SIREN AFTER HOURS EMERGENCY PHONE EMERGENCY PIN - Page 12 -...
Need help?
Do you have a question about the CYCLOPS PARALYSER 485 and is the answer not in the manual?
Questions and answers