Summary of Contents for BTX R3C K2100T2
- Page 1 Distributed by Advanced Capture Record Streaming Solutions USER MANUAL K2100T2 K2120T0, K2121T0 K2140T0, K2141T0 K3160T0 K3100T2 K4140T0 2019...
-
Page 2: Table Of Contents
Export Function ........... 37-38 PRE-CONFIGURING AV OVER IP SOURCES ......18 Editor Function ............ 39-41 ASSIGNING SOURCES TO CHANNELS ......19-21 HDMI and 3G-SDI Inputs ...........19 AV Over IP Inputs (ONVIF Enabled) ......20 AV Over IP Inputs (Non-ONVIF Enabled) ....21 www.btx.com... -
Page 3: R3C Advanced Features
3G-SDI and HDMI part of the presentation. Each input and the program content can be streamed live as HLS, RTMP, RTMP Push, and RTSP Hi and LO streams as well as transport streams. www.btx.com... - Page 4 Turn recorder on and off Note: this is a purpose-built computing device. Never disconnect the power or hold the power button down when the unit is on. It can corrupt the Storage medium and create a non volatile image in the system memory www.btx.com...
-
Page 5: Front Panel Features
Power button Note: this is a purpose-built computing device. Never disconnect the power or hold the power button down when the unit is on. It can corrupt the Storage medium and create a non volatile image in the system memory www.btx.com... -
Page 6: Rear Panel Connectivity
2.5mm pitch. RS-232 Serial Port COM_P Gigabit Ethernet Network interface (RJ-45) full duplex for external control Line-IN 3.5mm 2 channel Hi-Z unbalanced line in VGA_IN VGA connection (HD-15) AUDIO 3.5mm 2 channel Hi-Z unbalanced line out DC_IN Standard 19V DC power supply www.btx.com... -
Page 7: K2120T0
3 Pin (COM) for control of local tracking VGA_IN VGA connection (HD-15) devices, 4 Pin (Com-P) for external control COM_P of recorder. (2.5mm pitch x2) DC IN Standard 19V DC power supply USB3.0 Content transfer (x2) LAN connection (RJ45) www.btx.com... -
Page 8: K2220T0
3 Pin (COM) for control of local tracking Balanced MIC inputs with phantom power. devices, 4 Pin (Com-P) for external control (2.5mm pitch x2) COM_P of recorder (2.5mm pitch x2) VGA_IN VGA connection USB3.0 Content transfer (x2) DC IN Standard 19V DC power supply www.btx.com... -
Page 9: K2140T0
3 Pin (COM) for control of local tracking VGA_IN VGA connection (HD-15) devices, 4 Pin (Com-P) for external control COM_P of recorder. (2.5mm pitch x2) DC IN Standard 19V DC power supply USB3.0 Content transfer (x2) LAN connection (RJ-45) www.btx.com... -
Page 10: K3100T2
Programming and Service Port COM_P of recorder with RS232 port. (2.5mm pitch) 3 Pin (COM) for control of local tracking DC IN Standard 19V DC power supply devices with RS232 port. (2.5mm pitch) LAN connection (RJ-45) USB3.0 Content transfer (x2) www.btx.com... -
Page 11: K3160T0
HDMI Input 1 USB3.0 Content transfer (x2) COM1-2 Serial ports for PTZ control HDMI_IN1 HDMI Input 2 (2.5mm pitch x2) COM3 Balanced MIC inputs with phantom power. DC IN Standard 19V DC power supply MIC (5-0) (2.5mm pitch x6) www.btx.com... -
Page 12: K4140T0
HDMI in loop COM1-2 Auxilliary serial ports LAN connection (RJ-45) COM3 USB3.0 USB 3.0 ports (x2) DC IN DC power in Serial ports for legacy serial control Wi-Fi antenna connections (x4) COM_P Note: There are no Wi-Fi antenna connetions on K4140T02 www.btx.com... -
Page 13: Serial External Control Connection
SERIAL EXTERNAL CONTROL CONNECTION ALL MINRRAY RS-232 MINI DIN8 CONNECTORS TIA-568A Color TIA-568B Color Description WHT/GRN WHT/ORN (Not Used) (Not Used) WHT/ORN WHT/GRN Transmit Data Ground WHT/BLU WHT/BLU Receive Data WHT/ORN (Not Used) WHT/BRN WHT/BRN (Not Used) (Not Used) www.btx.com... -
Page 14: Serial External Control Connection
Phoenix (COM-P) Pin Description DB-9 Pin Phoenix (COM-P) Pin Description Ground SERIAL EXTERNAL CONTROL CONNECTION R3CI P2000 DETAIL PLU GGA BLE TERM INAL B LOCK CAT-5e SUPPLIED (Dongle 1 ) S U P P LIE D (D ongle 2) HEADER www.btx.com... -
Page 15: Setting Up The Appliance For The First Time
SETTING UP THE APPLIANCE FOR THE FIRST TIME: OUT OF BOX STEPS... -
Page 16: Configuring The Network Identity
192.168.1.55 to launch the log in screen. The default credentials to log in for the first time is: User: admin Password: admin This will direct you to the Director Page; the central control page for the K2 and K3 series equipment. www.btx.com... - Page 17 Device Settings page Click the advanced IP address settings button, then populate the network identity text boxes, and click OK. NOTE: The recorder must be restarted in order for the new IP settings to take affect. www.btx.com...
-
Page 18: Pre-Configuring Av Over Ip Sources
ONVIF enabled device like cameras and encoders. If the device you plan to connect by LAN is not ONVIF enabled, it can still be added manually. Please refer to page 20 for instructions on how to include both ONVIF compliant and noncompliant devices. www.btx.com... -
Page 19: Assigning Sources To Channels
The preview screen for this channel provides real time viewing of the changes. A Reset Button is provided if you do not achieve the desired results. When you are satisfied with the channel setup, click OK to accept the settings. www.btx.com... -
Page 20: Assigning Sources To Channels
After you select a source, its signal type, resolution, frame rate and state will be displayed in the window. Unlike discrete sources like 3G-SDI and HDMI, any encoded signal will not be adjustable and therefore, any picture adjustments should be made at the source. Click OK www.btx.com... -
Page 21: Av Over Ip Inputs (Non-Onvif Enabled)
Unlike discrete sources like 3G-SDI and HDMI, any encoded signal will not be adjustable and therefore, any picture adjustments should be made at the source. Click OK www.btx.com... -
Page 22: Director Interface All Models
DIRECTOR INTERFACE ALL MODELS Director Interface K2120T0 Director Interface K2220T0 Director Interface K2140T0, K4140T0 and K2100T2 Director Interface K3160T0 www.btx.com... -
Page 23: Director Interface (Depicted)
DIRECTOR INTERFACE (K2140T0 DEPICTED) Description Description The “S” above the Channel Sources. It stands for Sub Recording and means the alternate source to Layouts.) Streaming Appliance Dashboard Annotation Audio Transitions and Layouts PTZ camera controls www.btx.com... -
Page 24: Record
Press Pause to temporarily stop the recording. Press Start to resume the recording, glitch free. Press Stop to end the recording session. The file will be finalized and available for viewing within a few seconds. Click the gear to configure record parameters. www.btx.com... - Page 25 High Low streams so that users with limited bandwidth may still receive a live stream. Sending streams by 2 different protocols ie. RTMP streams for computer users using a player and HLS streams for mobile device users. Sending RTMP Push streams to 2 different CDN (Facebook AND YouTube) www.btx.com...
-
Page 26: Live Streaming Content
Press Start to begin streaming. The Start button will glow orange to confirm the appliance is streaming, and a count-up timer will Choose the frame rate. appear to the right of the controls to keep you informed of the elapsed streaming time. www.btx.com... - Page 27 Click the Copy button to copy the RTMP Stream key and paste it into the Name Text Box on the live streaming settings as described on the previous page. Follow the rest of the steps from the previous page, then return to the FaceBook live page (shown here) and click the Go Live button. www.btx.com...
-
Page 28: Transitions Between Sources
Reveal Top to Bottom to Top Left Diagonal Bottom Left Diagonal Top Right Bar Wipe Reveal Bottom to Top to Top Right to Bottom Left Diagonal Top Left to Reveal Left to Right Cut (Default) Transition Duration Bottom Right www.btx.com... -
Page 29: Layouts
All-Up layout, the channels without sources will display as “No Signal”.) Use the SWAP button to change the sources amongst the layout. Description Description Description Description Picture in Picture Diagonal Montage Swap Button PnP Size Options Side by side All-Up PnP Layout Options www.btx.com... - Page 30 TITLE AND LOGO FUNCTIONS Description To add or modify a title or logo, click the settngs gear. www.btx.com...
-
Page 31: Title And Logo
Choose a preset X and Y position. This is the preferred method for Logo placement. Windows MacOS Description To add a logo, click the Choose File button. Both Windows OS and Mac OS screens shown above. www.btx.com... - Page 32 To display the logo you selected, press the Logo button on the Director Page. The button will now be highlighted orange and the logo will show in the program window. www.btx.com...
-
Page 33: File Management
FILE MANAGEMENT Description On the Navigation Menu along the top, click the FILE MANAGEMENT tab. www.btx.com... -
Page 34: Overview
Delete files. Please see details on page 36 for more information. Export files or sessions. Please see details on page 37 & 38 for more information. Editor Function. Please see details on page 39 for more information. Content preview window File list page navigation. www.btx.com... - Page 35 Click the Session icon to view the content recorded for that session. It will include all the files you selected to record in record settngs. Click the Info button to view the individual file info. Description Click the Play button to review the file in the Content Preview Window. www.btx.com...
- Page 36 Click the Delete button. If you wish to delete all files on the local HDD check the all button (not recommended) Click to select the sessions -or- Individual files you wish to delete. When you are finished click the Delete button again. As depicted in the “After” picture the selected files and sessions are now permanently deleted. www.btx.com...
-
Page 37: Export Function
Click to select the sessions -or- Individual files you wish to export. When you are finished click the Export button again. As depicted the recorder will export each file individually so you may choose to rename the files individually. www.btx.com... - Page 38 Click to select the sessions -or- Individual files you wish to export. When you are finished click the Export button again. As depicted the recorder will export each file individually so you may choose to rename the files individually. www.btx.com...
- Page 39 FILE MANAGEMENT EDITOR FUNCTION Description Click the Editor button. The Editor interface will open on a new page. www.btx.com...
- Page 40 Show Audio Bin Bin (Selected above) Video Content Timeline Show Edited File Bin Editor Preview Window Audio Content Timeline Delete File Button and Export File button (Grayed out when Add Video Content Button Build (Render) File button no files exist) www.btx.com...
- Page 41 Click the Add Video button OR double-click the first open container on the timeline to add video files to the timeline. This opens a file list of content available on the appliance. Alternately, you can select a file on your computer by clicking the Local File button. NOTE: Any selected file MUST be MP4. www.btx.com...
- Page 42 Distributed by www.btx.com...
Need help?
Do you have a question about the R3C K2100T2 and is the answer not in the manual?
Questions and answers