HYMAX GRIP FLANGE ADAPTOR Installation Instructions

DO NOT DISASSEMBLE THE COUPLING. DO NOT LUBRICATE THE BOLTS.
HYMAX GRIP FLANGE ADAPTOR 3"-12"

GENERAL INSTRUCTIONS:

HYMAX GRIP FLANGE ADAPTOR 3"-12"
THE HYMAX GRIP FLANGE ADAPTOR IS A STAB-ON TYPE RESTRAINT THAT IS APPROVED FOR USE WITH METAL
HYMAX GRIP FLANGE ADAPTOR 3"-12"
AND PLASTIC PIPES.
STEP 1
STEP 2
STEP 3
1
HYMAX
FLANGE ADAPTOR
(1.5"-12")
Installation Instructions
WARNING: DO NOT ATTEMPT TO USE THE HYMAX GRIP ON AC OR FRP PIPE!

PRECAUTIONS FOR HDPE PIPE:

WHEN USING THE HYMAX GRIP FLANGE ADAPTOR ON HDPE PIPE.
HYMAX GRIP FLANGE ADAPTOR
3"-12"
FOR OTHER MATERIALS, PLEASE CONTACT KRAUSZ USA OR YOUR KRAUSZ DEALER.
HYMAX GRIP FLANGE ADAPTOR
3"-12"
HYMAX GRIP FLANGE ADAPTOR
3"-12"
Prepare pipe end by de-scaling if required. Clean the pipe as required with
water. Make sure that the pipe is clean from debris and defects that interfere
STEP 1: Clean the pipe as required with HYMAX GRIP's proper seal.
with water. Make sure that the pipe is
clean from debris and defects that STEP 1: Clean the pipe as required
NOTE: Except steel, PVC, and PE pipes, all rough-surfaced pipes must be lubricated
with water. Make sure that the pipe is interfere with HYMAX Grip's proper seal.
with a water-based gasket lubricant in order to achieve a proper seal.
clean from debris and defects that
STEP 1: Clean the pipe as required
interfere with HYMAX Grip's proper seal.
with water. Make sure that the pipe is
clean from debris and defects that
interfere with HYMAX Grip's proper seal.
Measure the pipe's Outer Diameter and make sure the coupling's size fits properly.
STEP 2: Measure the pipe's Outer
Diameter and make sure the coupling's
NOTE: Each coupling's size range is shown on the product's label. Make sure that
STEP 2: Measure the pipe's Outer size fits properly.
the pipe is not out of round! The pipe should be free of scratches, dents, flats or
Diameter and make sure the coupling's
size fits properly.
STEP 2: Measure the pipe's Outer
other defects which may interfere with the HYMAX GRIP Flange Adaptor's proper
Diameter and make sure the coupling's
seal. The GRIP Flange Adaptor may not fit well or function properly on a pipe which
size fits properly.
is damaged or is out of round.
STEP 4: Mark pipe end to a minimum
required stab depth of 3.5". These marks
Unpack the HYMAX GRIP Flange Adaptor carefully. Inspect the product and end ring
indicate the required stab depth of the STEP 4: Mark pipe end to a minimum
required stab depth of 3.5". These marks
pipe on the Flange Adaptor. for shipping damage and assure all parts are present.
indicate the required stab depth of the
STEP 4: Mark pipe end to a minimum
pipe on the Flange Adaptor. Inspect the end ring. If it is not centered on the HYMAX GRIP Flange Adaptor - DO
required stab depth of 3.5". These marks
indicate the required stab depth of the
NOT USE! Contact your distributor for return and replacement.
pipe on the Flange Adaptor.
NOTE: HYMAX GRIP Flange Adaptor is a stab-on type product. Do not loosen or
remove the end ring bolts.
NOTE: Make sure that the product fits the flange standard of the flanged product
you need to connect it to. The Flanged standard types appear in the submittal
Step 6A: Connect The Grip Flange Adaptor
to the existing flange....
drawings.
STEP 6a: Connect the GRIP Flange Adaptor
to the existing flange....
STEP 6a: Connect the GRIP Flange Adaptor
GRIP
®
THE USE OF FULL CIRCLE STIFFENERS IS REQUIRED
STEP 6b: .... and tighten bolts
to maximum.
STEP 6b: .... and tighten bolts
to maximum.
STEP 6b: .... and tighten bolts
to maximum.
STEP 6c: .... Bring in the pipe.
Stab the pipe onto the Flange
Adaptor so it covers the STEP 6c: .... Bring in the pipe.
mark on the pipe drawn Stab the pipe onto the Flange
Adaptor so it covers the in step #4 above.
STEP 6c: .... Bring in the pipe.
mark on the pipe drawn
Stab the pipe onto the Flange
in step #4 above.
Adaptor so it covers the
mark on the pipe drawn
in step #4 above.
Step 7: Tighten The End Ring
using a torque wrench, to the
STEP 7: Tighten the end ring
correct torque shown on the
using a torque wrench, to the product's label. By tightening
correct torque shown on the bolts the Flange Adaptor is steadily
STEP 7: Tighten the end ring
product's label. By tightening stabbed on the pipe.
using a torque wrench, to the
bolts the Flange Adaptor is steadily
correct torque shown on the
stabbed on the pipe.
product's label. By tightening
bolts the Flange Adaptor is steadily
stabbed on the pipe.
STEP 8: Make sure that the pipes
are not touching each other inside
STEP 8: Make sure that the pipes the body of the HYMAX GRIP.
are not touching each other inside There must be space between the
pipes in order for "Continuous the body of the HYMAX GRIP.
STEP 8: Make sure that the pipes
Dynamic Deflection" (CDD) to There must be space between the
are not touching each other inside
pipes in order for "Continuous take place.
the body of the HYMAX GRIP.
Dynamic Deflection" (CDD) to
There must be space between the
take place.
pipes in order for "Continuous
Dynamic Deflection" (CDD) to
take place.
is the creator of HYMAX