Advertisement
Quick Links
Brilliant
Wonders
LED WATERFALLS
Be sure that the electrical system prior to installation conforms to all local codes and
ordinances. A licensed or certified electrician must install the electrical system to insure
that it follows all of the requirements of the National Electric Code (NEC). The electrician
may need to consult the local building inspector for code interpretation before installing
the 25650-100 wireless controller.
Attention Installer: This manual contains important information about the installation,
operation, and safe use of this product. This information should be given to the owner
and/or operator of this equipment. When installing and using this electrical equipment,
basic safety precautions should always be observed.
Read all safety precautions and important instructions before attempting any electrical
wiring. Ensure that all power has been turned off at the power source. Failure to follow
safety warnings and instructions can result in severe injury, death, or property damage.
CMP recommends installation to be performed by a licensed professional.
Thank you for choosing the CMP 25650-100 series controller. If you haven't already done
so, please take a moment to read our safety information. To fully enjoy the features of
this controller, please read the entire manual before operating. Following these safety
requirements should prevent any damage to your new controller.
1. PERFORMANCE PARAMETERS
CONTROLLER
•
Power input: 12 Volt DC
•
Max Current: 5A x 3CH Max 15A
•
Maximum load power: 180 Watts
•
Change Mode: 32
• Scale Levels: 65536 steps/RGB
(16Bits/CH)
• Control Function: 8 touch buttons
•
Operating temp: -30°C to 55°C
•
Dimension: L8.3 in. x W1.6 in. x H1.2 in.
•
Weight(net): 180g
OPERATION & INSTALLATION QUICK REFERENCE
TM
WARNINGS AND IMPORTANT SAFETY PRECAUTIONS
IMPORTANT NOTICE
Wireless Touch LED RGB Remote Controller
INTRODUCTION
REMOTE
•
Power: Rechargeable 5 Volt DC
built in Lithium battery
•
Working Current: 30mA
•
Working Frequency: 2.4 GHZ
•
Battery Capacity: 1000mAh
•
Charge Time: <4 hours
•
Normal Usage Time: 30 days
•
Number of charge cycles: 500
•
Operating range: up to 90 feet
(dependent on environment)
•
Operating temp: -30°C to 55°C
•
Dimension: 5.7"L x 2.2"W x 0.9"H
•
Weight(net): 200g
25650-100 Series
Advertisement
Summary of Contents for Brilliant Wonders 25650-100 Series
- Page 1 CMP recommends installation to be performed by a licensed professional. INTRODUCTION Thank you for choosing the CMP 25650-100 series controller. If you haven’t already done so, please take a moment to read our safety information. To fully enjoy the features of this controller, please read the entire manual before operating.
-
Page 2: Key Features
2. KEY FEATURES The remote control has 18 function buttons and 1 full-color touch circle. The controller has 8 touch buttons. HOW TO PAIR THE CONTROLLER WITH THE REMOTE Press the “ON/OFF” key on the controller until you hear the “BEEP” sound, then press the “1”... - Page 3 3. INSTALLATION AND WIRING DIAGRAM Connected to RGB module as an example CLASS 2 POWER DC12V SUPPLY DC12V Note: Ensure all wire connections and polarities are correct before applying power. CONTROLLER MOUNTING You must provide the controller enclosure The enclosure or junction box must be installed per the National Electric Code (NEC) requirements as well as comply with any local codes and regula- tions b.
- Page 4 4. CHARGING METHODS 1. When charging, connect the USB cable to the mobile charger or a computer with USB interface. The remote control must be turned on to charge. 2. The blue indicator light flickers while charging, and will turn green when fully charged 3.
Need help?
Do you have a question about the 25650-100 Series and is the answer not in the manual?
Questions and answers