Summary of Contents for INFLOOR 24535
- Page 1 Operating Instructions Infloor Sales & Service SW Adjustable Manual Pressing Tool 24535 and 24538 (July 2008)
-
Page 2: Table Of Contents
Index 1, Structure of Infloor Sales & Service SW adjustable manual pressing tools ....P-3 2, Available jaws ........................P-4 3, Preparation before use ....................P-4 ................... P-4 Step 1, Choose correct pressing jaws ............P-5 Step 2, Mount appropriate pressing jaws on to pressing tool .................... - Page 3 The key operation instruction of pressing tool 24535 is similar to 24538 except two points: 1) The 24535 doesn’t need longer handles and is only for press fitting sizes 1/2” to 5/8”. The 24538 is for press fittings 1/2” to 1” , and doesn’t need longer handles to deal with the 1/2”...
-
Page 4: 2, Available Jaws
2, Available jaws The pressing jaws used on the pressing tool 24535 are smaller than the jaws on pressing tool 24538, therefore could not be interchangeably mounted on 24538, please refer to the following table for the corresponding jaws for them and read the notes carefully. -
Page 5: Step2, Mount Appropriate Pressing Jaws On To Pressing Tool
Step2, Mount appropriate pressing jaws on to pressing tool A, You need to open the pressing tool handles and then take off two screws (Part No.1,M6 × 25), see following picture. B, Position the two opposite jaws in the pressing tool head, make sure the two jaws are evenly well positioned and the specification number on the two jaws are on the same side, then fix the jaws with the screws (Part No.1,M6 25). -
Page 6: Step3, Adjustment For Pressing Tool
Pressing-Force to fully close the pressing tool jaws should be about 33 LBS. If not, then the pressing tool need adjustment before use, please refer to next step for adjustment. Step3, Adjustment for pressing tool A, Open the pressing tool and release the "locking screw" (Part No. 13) counter-clockwise for about 3 rounds. -
Page 7: 4,Cautions And Parameters For Pressing Tool Adjustment
3/4" and 1" mounted with lengthened handles. 5, Special operations at corners or narrow spaces Infloor Sales & Service adjustable manual pressing tools provide special design for occasions where there isn’t enough space to open the handle or lengthened handles such as corners or narrow... - Page 8 A, Close the pressing tool, release and take off the butterfly-shape screw (Part No. 16 ), B, Open the pressing tool, then take off the pin(Part No. 6) fixed with the butterfly-shape screw. C, Now you can adjust the angle from pressing tool head to pressing tool handles, to make sure the jaws are rightly positioned over the sleeved-fittings and you can open the pressing tool enough to press fittings.
-
Page 9: 6, Pressing F5 (U-Profile) Fittings With The Pressing Tool
D, Mount back the pin and the butterfly-shape screw onto the pressing tool. Put the pressing tool on right position and close the handles to finish the pressing procedure. E, Release and remove the butterfly-shape screw and the pin from the pressing tool, if necessary take off the lengthened handles,then open the jaws and move the pressing jaws away from the pressed fitting without opening the handles or lengthened handles. -
Page 10: 7, Pressing Tool Wears And Final Rejection
C, Close the pressing tool to press the fittings,the contact points on right and left handles(Part No. 10 and 11) must contact. Contact Contact 7, Pressing tool wears and final rejection Over a long time use, the pressing tool components/parts might wear out badly, the Trial-Pressing- Force may not be able to reach about 33LBS or pressing jaws may not be able to be closed completely in pressing fittings even after adjustment. -
Page 11: 8, Preservation And Maintenance
Infloor Sales & Service 24535 and 24538 pressing tools were tested 5000 times with positive results. In this testing process, necessary adjustments were made on the pressing tool, but without any replacement of pressing tool parts/components. 8, Preservation and maintenance A, When the tool is not in use, it should be kept in either of the following ways: ... - Page 12 E. In use or tool adjustment,the screws or pins taken off from the pressing tool should be well preserved. We wish we have been of good service to you,if you have any questions on using our pressing tools, please feel free to direct your questions to us at info@infloor.com...