Advertisement
Quick Links
Tapco Products Company
"The World Leader
in Specialty Tools
for the Professional"
Contents
Page
General Instructions ... 2
Knife Set Up ................ 2
Accessory Set Up ....... 3
Parts List ..................... 4
Motor Set Up ............... 5
Slitter Stand Set Up .... 6
Optional Slitter
Cut-Off ..................... 7
Optional Knives .......... 8
®
Port-O-Slitter
OPERATIONS MANUAL
General instructions, set up, accessories and guide to using your
portable precision slitting, rib forming and perforating system.
24" model Port-O-Slitter with
optional Port-O-Slitter Stand,
Cut-Off and PRO-Coiler.
(see page 6)
®
U.S. & Foreign Pats. Pend.
Tapco Port-O-Slitter is
"The Siders Helper" use it in
the shop or on the job site.
Advertisement
Summary of Contents for Tapco Port-O-Slitter
- Page 1 Accessory Set Up ..3 Parts List ..... 4 Motor Set Up ....5 Slitter Stand Set Up ..6 Tapco Port-O-Slitter is 24" model Port-O-Slitter with Optional Slitter optional Port-O-Slitter Stand, “The Siders Helper” use it in Cut-Off ..... 7 Cut-Off and PRO-Coiler.
- Page 2 PORT-O-SLITTER SETUP AND OPERATION 1. ASSEMBLY OF YOUR PORT-O-SLITTER Remove the contents of the PARTS BAG, which should include 2 “T” WRENCHES and the CRANK HANDLE ASSEMBLY. Install the HANDLE and tighten the SET SCREW against the “flat” on the SHAFT. Make sure that the HANDLE turns freely without interference.
- Page 3 MAINTAINING AND LUBRICATING YOUR PORT-O-SLITTER • Keep a light film of protective oil on the SHAFTS, DRIVE GEARS, SET SCREWS, and when not in service, the KNIVES. Always inspect KNIVES for dirt and other foreign matter before using. Never clean knives while slitter is in operation.
-
Page 4: Parts List
PARTS LIST *NOTE: Please see page PORT-O-SLITTER PARTS 8 for accessories Part No. Description Part No. Description Part No. Description 10020 1/4-20 X 5/8" Hex Button HD 10597 Pivot Bracket - Left 10619 5/16" Knurled Knob 10076 10-24 X 3/4" Phil Pan HD... - Page 5 Port-O-Slitter Motor Kit Setup/Parts List STEP 4 STEP 1 Set the reducer onto the motor base plate with the cou- Attach steel connector brackets to the motor base plate plings facing each other. Place the sleeve between each using 1/4-20 x 7/8" hex bolts, 1/4" flat washers and 1/4-20 coupling flange and draw together so the ends of the Nylox hex nuts.
- Page 6 Port-O-Slitter Slitter Stand Set-Up/Parts List 24" Port-O-Slitter Lay out both end assemblies and attach the cross braces by inserting the register pins into the center holes in the outside channels and tightening the “T” knobs securely into the top holes (see detail).
- Page 7 Port-O-Slitter Cut-Off Set-Up/Parts List Note: Reference numbers may only appear once on duplicate parts. Optional Slitter Cut-Off makes factory quality cut offs right on your Port-O-Slitter. Saves time and increases production. Rubber Bumper Installation Remove rubber bumper on end of track, slide Cut-Off on and replace bumper.
- Page 8 ACCESSORIES SLITS RIB-FORMS PERFORATES silver silver FOR VINYL PERFORATING ROLLS GROOVED KNIFE SET Optional knives are necessary " SHAFT (#11475) to perform some operations. Performing 2" SHAFT #11474 2" SHAFT (#11476) all operations shown above at one time is not recommended. For slitting narrow strips of material, place Place male roll into grooves atop female roll.
Need help?
Do you have a question about the Port-O-Slitter and is the answer not in the manual?
Questions and answers