All manuals and user guides at all-guides.com GENERAL DESCRIPTION AKIRA AKTP01 is a CTV monolithic chassis currently developed by AKIRA Co. It introduces a monolithic IC TB1238AN developed by Toshiba Co. To carry out all the small signal processing TB1238AN is a kind of IC used by color TV in PAL/NTSC system, which is controlled by Inter IC Bus.
Do not hold the CRT neck in case of causing damage to the CRT. 2. When the power cord needs replacing, use the same one as that provided by AKIRA factory. 3. Voltage exists between the hot and cold ground when TV is in operation. Install a separation transformer during repairing or connecting to any tester for the sake of safety.
COLOUR PURITY ADJUSTMENT and CONVERGENCE ADJUSTMENTS procedures. ADJUSTMENT MODE B+ adjustment, TV signal receiving Item AKPH01 chassis Measuring No. 5 Service Remote Controller Equipment Preparation The set is turned on and work normally. Before Adj. No signal input Model No: CT-21FGS1 Version 1.0...
Page 8
Press V+ or V- key, to select SEARCH or AUTOMEMORY item, press P+ key to start searching. Press P+ or P- key to inspect the set if there is channel skipped, if so, searching again by SEARCH as above described. Model No: CT-21FGS1 Version 1.0...
Page 9
6. Press R+ or R- (with the red block), G+ or G- (with the green block) and B+ or B- (with the blue block) key respectively, to adjust a horizontal line appeared to the white colour. 7. Press key again and changing back to normal screen. Model No: CT-21FGS1 Version 1.0...
Page 10
(which is according to the specification of factory’s adjustment) 3. Press R+ or R-, G+ or G- and B+ or B- key respectively to adjust the white balance of low light until the white balance of high and low light is good Model No: CT-21FGS1 Version 1.0...
Page 11
3. Item OSD position adjustment AKTP01 chassis Measuring No.1 and No.5 service remote controller Equipment Preparation Brightness, contrast and color should be set in standard before Adj. Model No: CT-21FGS1 Version 1.0...
Page 12
X (mute), DISP (display), PP and SLEEP key respectively, the relevant function should 6. Press be normal 7. Press S-OUT key on No.5 service remote controller to set default value that stored in E 2 PROM on the chassis for product shipment. Model No: CT-21FGS1 Version 1.0...
Check V411,T402,T401, C515,C517,V411, Deflection coil VD552-VD555 115V Test the voltage of C415,C416,T402 D901 pin7 C412 Check T402,V411,R449 Check T402 Check L414,VD403,C411 4.5-5.5V Deflection coil CPU has sent the Check if V572 Power-off signal is broken down Model No: CT-21FGS1 Version 1.0...
Page 14
Check the voltage on the C992 CheckN902, TUN101 0-33V Check R102, C102, TUN101 Check N101,R968,R969, The voltage between VL and BH vary from N201,A101 0V to 9V or not when auto searching Check ,V975,D901, R973, R975 ,R975,R990,C971,C972,C991 Model No: CT-21FGS1 Version 1.0...
Page 15
Check if voltage on pin 48 of N201 is 4.6V Check R321,VD436,T402,R462,C452 Check C212,TUN101,N201 Observe if these is snow-noise-wave disturbance on the CRT via using “ Signal-input way ” by touching pin 18,19,20 of N201 Check R273,R271,R272,V602,V612,V622,N201 Model No: CT-21FGS1 Version 1.0...
Page 16
The voltage on pin 9,10,11of N252 Check VD552,R910,C700,T501,N701 Hear if there is the voice liking “Ka…Ka ” in the loudspeaker via using “ Signal-input way ” by touching pin 2 of N711 Check D901, N252,N203 Check SP301, SP302, N711 Model No: CT-21FGS1 Version 1.0...
Page 17
The deflection yoke on the CRT Check R908, C448, N402, N201 Abnormal Measuring the waveform on pin 2 of N402 Check N402 Normal Measuring the waveform on the deflection yoke Abnormal Check R442,C413,VD433,XZ411, deflection yoke Model No: CT-21FGS1 Version 1.0...
Page 18
The horizontal yoke is opened or not Repair CRT Whether “ XZ411” is opened Check if there is bad solder between XZ411, and the main board Check L414, VD403, C412,C415,especial in inductive components and connector Model No: CT-21FGS1 Version 1.0...
Page 19
Check R939,VD922 Check T501, VD553,R558 Check D901 Check the voltage on the emitter of V925 4.98V 4.98V Check the voltage on the positive pole of VD921 Check R937 4.98V =3.6V Check VD921, R933 Check R932,R937,V925 Model No: CT-21FGS1 Version 1.0...
Page 20
We can judge this failure by measuring the wave of the character in an oscilloscope. The detail checking and repairing steps are as follow: No OSD Check the wave on the pin 4 of FBT and N402 pin7 Check V922, V923,R914, VD436, R449, D901 Check FBT T402,N402 Model No: CT-21FGS1 Version 1.0...
S B-Y IN SECAM B-Y signal input Y IN Luminance signal input H AFC Connecting RC network for horizontal AFC filter EXT.VIDEO/Y IN External video/luminance signal input DIG.GND Digital circuit ground TV.VIDEO IN TV. video signal input Model No: CT-21FGS1 Version 1.0...
Page 22
VCO VCC +9V supply input (IF VCO circuit) Limiter IN Sound IF signal input RIPPLE FILTER Ripple filer circuit EXT AUDIO External audio signal input FM DEC NF FM direct current negative feedback filter capacitor can Model No: CT-21FGS1 Version 1.0...
Page 23
Video mode selection control No.1 REMOTE Remote controller signal input H.SYNC Horizontal sync signal input SCL0 IIC-BUS SCL0 SDA0 IIC-BUS SDA0 S-ID S-VIDEO Detection SIF1 SIF data output1 SIF2 SIF data output2 5V power supply Model No: CT-21FGS1 Version 1.0...
Page 24
Decoder output 1 OUT2 Decoder output 2 Band control level input 1 Band control level input 2 Connect to ground +33V supply input pin OUT3 Decoder output 3 OUT4 Decoder output 4 +12V supply input pin Model No: CT-21FGS1 Version 1.0...
Page 25
The pin for input 4.43MHz of carrier wave for self-adjustment 4.43MHz CW IN circuit. ID SW The switch pin for selecting the ID detection mode. SECAM ID IN/OUT The interface pin to the main processor TB1238AN Model No: CT-21FGS1 Version 1.0...
Page 26
Vertical S correction/50 Hz VLIS Vertical line deflection of 60 Hz HIT0 50Hz SIZE ZOOM/WIDE V. HIT1 60Hz SIZE ZOOM/WIDE V. SECAM B-Y Black SECAM R-Y Black RAGC RF AGC PIF VCO center HAFC AFC gain Volume 25% Model No: CT-21FGS1 Version 1.0...
Page 27
Sub tint min(difference) Sub sharp center(3.58NTSC TV) Sub sharp center(3.58NTSC AV) Sub sharp center(OTHER TV) Sub sharp center(OTHER AV) SHPX Sub sharpness max(difference) SHPN Sub sharpness min(difference) TXCX Text RGB contrast max RGCN Text RGB contrast min Model No: CT-21FGS1 Version 1.0...
Page 28
SELF CNTC Self adjust CNTC initial data SELF TNTC Self adjust TNTCinitial data SELF COL Self adjust COL initial data OSD position Factory Data NOTE: The data provided in the form provides to consult only! Model No: CT-21FGS1 Version 1.0...
Need help?
Do you have a question about the CT-21FGS1 and is the answer not in the manual?
Questions and answers