Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Logic IO RTCU AX9i eco
- Page 1 RTCU AX9i eco Technical Manual Version 1.01...
-
Page 2: Introduction
- meeting the requirements of today’s most demanding and sophisticated M2M/IoT applications. The RTCU AX9i eco rests on the RTCU M2M Platform that brings all the necessary tools together to develop, implement and maintain today’s sophisticated M2M/IoT applications. -
Page 3: The Technical Highlights Of The Rtcu Ax9I Eco
RTCU AX9i eco Technical Manual V1.01 The technical highlights of the RTCU AX9i eco: Based on the RTCU M2M Platform X32 execution architecture. o RTCU IDE development tool with a full featured device simulator. o Huge standard API with more than 800+ functions. - Page 4 RTCU AX9i eco Technical Manual V1.01 * * * * THIS PAGE IS INTENTIONALLY LEFT BLANK * * * Logic IO ApS. Ph: (+45) 7625 0210 Holmboes Allé 14 Fax: (+45) 7625 0211 8700 Horsens Page 4 of 30 Email: support@logicio.com Denmark www.logicio.com...
-
Page 5: Table Of Contents
RTCU AX9i eco Technical Manual V1.01 Table of Contents Introduction..............................2 The technical highlights of the RTCU AX9i eco: ..................3 Graphical view ..............................6 Connection Overview..........................7 Power supply ..............................10 DC Supply ..............................11 AC Supply ..............................12 Digital I/O ...............................14 Relay outputs .............................14 Load Noise ..............................14 Digital inputs / S0 inputs / wakeup (ignition) input ................15... -
Page 6: Graphical View
RTCU AX9i eco Technical Manual V1.01 Graphical view On the front of the RTCU AX9i eco are four user controlled LED’s and three system LED’s for simple information and status. System LEDs User Controlled LEDs The external GSM antenna connector is located at the side of the device as shown below: Logic IO ApS. -
Page 7: Connection Overview
The angled terminals contain connections for the communication interfaces: RS232 Port 1 and 1- Wire. Also located inside the RTCU AX9i eco are the SIM card reader, DIP switches and a USB-B high- speed programming connector. Logic IO ApS. - Page 8 RTCU AX9i eco Technical Manual V1.01 Stacked terminal overview Terminal Name Description TOP row BOT row Contact set for relay output 1 Contact set for relay output 2 Contact set for relay output 3 Contact set for relay output 4 Not connected Protective Earth terminal for AC supply.
- Page 9 RTCU AX9i eco Technical Manual V1.01 Angled terminal front row overview Terminal Name Description SER1_TXD Transmit data from serial port 1, RS232 compatible SER1_RXD Receive data for serial port 1, RS232 compatible DEV_DET Reserved for accessories. SGND Signal ground 1Wire...
-
Page 10: Power Supply
Dual Supply Note: The RTCU AX9i eco unit can be supplied with both VAC and VDC at the same time. The unit will run on the VAC supply if the VDC supply voltage is < +16VDC. If the VDC supply voltage is higher it will run on the VDC supply. -
Page 11: Dc Supply
Positive power is applied to the DCIN pin and ground is connected to the XGND pin. The DC supply of the RTCU AX9i eco is protected against wrong polarity. If a system ground are connected to either SGND or AGND a wrong polarity on the supply lines will destroy the internal GND connection. -
Page 12: Ac Supply
RTCU AX9i eco Technical Manual V1.01 AC Supply The RTCU AX9i eco unit can be supplied with 85-265VAC (50/60Hz) from a standard wall plug or any other high-voltage VAC power rail. The AC supply of the RTCU AX9i eco is a high-efficient switch mode power supply and the AC input is protected with a 1A/250V Fast Acting fuse. - Page 13 RTCU AX9i eco Technical Manual V1.01 Please Note: The DC ground of the AX9 series is isolated from the AC ground because of the nature of AC-to- DC converting. As these two grounds are not tied together anywhere in the AX9, the DC ground may appear as "floating ground"...
-
Page 14: Digital I/O
RTCU AX9i eco will switch to normally-open. The RTCU AX9i eco unit offers a very advanced power management, which makes it possible to have one or more outputs enabled while the RTCU is in low power mode. Please consult the RTCU IDE on-line help for more information. -
Page 15: Digital Inputs / S0 Inputs / Wakeup (Ignition) Input
SGND and the appropriate input will activate it. This is used in most electricity metering equipment. Please note: The RTCU AX9i eco unit must be supplied with a minimum of 16 VDC or AC power for the S0 mode to work correctly. - Page 16 RTCU AX9i eco Technical Manual V1.01 Wakeup (ignition) input The DIN5 / wakeup (ignition) input is a special input in that it also functions as the wakeup input. If the input is activated with a logical high or low (Wait For Event mode only) when the RTCU AX9i eco is in low-power mode it will wake-up the unit.
-
Page 17: Analog Input
RTCU AX9i eco Technical Manual V1.01 Analog input The RTCU AX9i eco unit has two analog inputs which can be configured individually to work either as voltage or current measurement inputs by using the configuration jumper. The range in voltage mode is 0-10VDC and in current mode it is 0-20mA. -
Page 18: Usb Programming Port
A standard USB cable can be used between the unit and the PC. RS232 communication ports (EIA/TIA-232 and V.28/V.24 compatible) One general purpose RS232 ports available on the RTCU AX9i eco unit. The serial input is compliant with the EIA/TIA-232 standard. -
Page 19: 1-Wire Bus
For 1-Wire ID-Button readers, which include a built-in LED, a dedicated output is available for this purpose. Please consult the RTCU IDE documentation for further information. For further information regarding modular 1-wire concept, please refer to the document “Modular 1-Wire Concept Technical Manual” on the Logic IO webpage. 1-Wire terminals Name... -
Page 20: System Led S1 And S2
RTCU AX9i eco Technical Manual V1.01 System LED S1 and S2 The RTCU is equipped with two system LED’s which shows the status and possible errors of the RTCU unit. The different patterns are listed in the table below. If the color of the system LED S1 is yellow, the unit is actively communicating with the RTCU IDE (or another program, supporting the RTCU RACP protocol). -
Page 21: Switches
Switches DIP-Switch The RTCU AX9i eco unit contains four dipswitches, where three of them are available for the application to use (fourth dipswitch is reserved for GSM antenna switching.) The dipswitches are located inside the unit (see drawing below or graphical view) System switch (RST) The RTCU AX9i eco unit contains a combined reset/diagnostic switch. -
Page 22: Internal Li-Ion Battery
• Avoid strong impacts and shocks. • For more information regarding the environmental limitations, see “Specifications for RTCU AX9i eco” below or consult the RTCU AX9i eco datasheet. Logic IO ApS. Ph: (+45) 7625 0210 Holmboes Allé 14 Fax: (+45) 7625 0211... -
Page 23: Gsm
• GSM Antenna The RTCU AX9i eco offers support for both an on-board internal GSM antenna and a user supplied external antenna connected to the SMA female connector at the top of the encapsulation. The active antenna can be selected by the application using the gsmSetAntennaMode function or alternatively with a DIP switch. -
Page 24: Sim-Card
Please refer to the RTCU IDE online help for further information on gsmSetAntennaMode. When installing the RTCU AX9i eco please make sure that the antenna is not in close proximity of metallic parts or anything else that can influence the efficiency of the GSM antenna. -
Page 25: Power Consumption
Please Note: Values marked with (*) is average and should be considered as guidelines as they may vary depending on the GSM signal strength. External DC supply When the RTCU AX9i eco unit is powered from an external DC power source the power consumptions will be as follows. Maximum power consumption... -
Page 26: External Ac Supply
RTCU AX9i eco Technical Manual V1.01 External AC supply When the RTCU AX9i eco unit is powered from an external AC the power consumptions will be as follows: Maximum power consumption 220VAC Unit active Unit active with GSM on* GSM idle @ -67dBm*... -
Page 27: Appendix A - Unit Configuration Guide
RTCU AX9i eco Technical Manual V1.01 Appendix A – Unit configuration guide The RTCU AX9i eco has many features and some of them require configuration by using hardware jumpers inside the unit. A brief overview over the jumper settings can be found on the following... - Page 28 RTCU AX9i eco Technical Manual V1.01 JPAI1 and JPAI2 These jumpers are used to select between current and voltage input. With a jumper installed on the relevant analog input it will measure current between 0-20mA. JPDI1, JPDI2, JPDI3 and JPDI4 These select either normal or Class A S0 input for DIN1-4.
-
Page 29: Appendix B - Installing The Sim Card
RTCU AX9i eco Technical Manual V1.01 Appendix B – Installing the SIM card The SIM card reader is a lid based type with a mechanical lock for secure installation of the SIM card. Open the hinged lid of the SIM card reader, orientate the card as showed below, and insert it into the lid of the card reader. -
Page 30: Rtcu Ax9I Eco Specifications
RTCU AX9i eco Technical Manual V1.01 RTCU AX9i eco Specifications Processor and Main-memory Electrical Specification. Internal Interfaces. • Powerful 32-bit ST ARM7 processor. • Supply operating range: • Screw-terminals for: 8 to 36 VDC. Power and I/O. • 1088 KB fast execution RAM.