Subscribe to Our Youtube Channel
Related Manuals for Bpt KX8O16A
Summary of Contents for Bpt KX8O16A
- Page 1 KNX 8-channel 16A actuator - DIN rail mounting KNX 12-channel 16A actuator - DIN rail mounting KX8O16A KX12O16A Technical Manual 24809180/24-02-2014...
-
Page 3: General Information
- General information Priorities: Dynamic administration of group addresses Priority Function Maximum no. of group addresses and associations: 152 Highest priority Relay state after bus voltage failure Disable function Device selection: Priority function Logic operation The application must first be adapted to the hard- Priority control ware in use. - Page 4 Important for the reconfiguration of switch actuators in occupied No short switching times may be parameterised buildings so that the outputs do not switch in the event of under load (see the technical data for the switch a download. The device does not know the status of the output) channel at this point and therefore no status signal can take place.
- Page 5 Relay operation - Relay operation: break contact The operation mode of the relay can be set via the parame- The relay contact can be operated logically as a break con- ter “Relay operation”. The relay can be used as a “break con- tact (via software).
-
Page 6: Status Response
Switch (changeover contact for channel 1/2) Flash for ON Switching on Switching off Status actuated telegram telegram not actuated Relay closed Relay status of Relay status of channel A channel A closed closed open open open Status response remains remains open closed closed... -
Page 7: Communication Objects
Switching functions Communication objects - Switching The following communication objects can be selected: Binary bus telegrams (EIS1 telegrams, 1 bit) are received via the Per channel: “Switch object” and converted into switching states (relay open/ Function Object name Type Prio Flags Behaviour relay closed). - Page 8 Per channel: Per channel: Set the central switching function. Function Object name Type Prio Flags Behaviour Central function Channel X Switch object 1 bit Receive Parameter Setting Channel X OFF at 0 or 1 Parameters ON at 0 or 1 ...
- Page 9 Non-retriggerable OFF delay ON and OFF delay Make contact function Break contact function telegram telegram, telegram, switching switching Status actuated Relay status Relay status closed closed not actuated t off t off t off open open Actuated t on t on t off...
- Page 10 flashes while the staircase lighting function is active. In the Retriggerable staircase lighting function with manual OFF function relay mode “flash for OFF”, the output flashes whenever the staircase lighting function is not activated. telegram Staircase lighting function Status Make contact function Break contact function actuated telegram,...
- Page 11 Communication objects Communication objects The following communication objects can be selected: The following communication objects can be selected: Per channel: Per channel: Function Object name Type Prio Flags Behaviour Function Object name Type Prio Flags Behaviour Channel X Switch object 1 bit Receive Channel X...
- Page 12 - OFF delay and staircase lighting function Communication objects The OFF delay can only be activated when a pure switching The following communication objects can be selected: function is selected or when combined with the setting Per channel: “staircase lighting function with manual OFF”. The param- eters for the OFF delay are not displayed in the setting Function Object name...
-
Page 13: Disable Function
Higher-level functions Disable function for: Disable object = 1; Value of disable object after bus voltage recovery: 0; Reaction at blocking: no change; Reaction at activa- With regard to the switching behaviour of the actuator, the tion: follows switch object higher priority functions take precedence over the switch- ing function, staircase lighting function and time delays. - Page 14 Parameters Set the flashing interval for the device if required. Per channel: Switch on the ON/OFF delay, staircase Flashing interval lighting function and disable function. Parameter Setting 100 ms Flashing interval base Channel X: General Parameter Setting 1 min Disable function switched off 1 hr...
-
Page 15: Logic Operations
AND logic operation; Value of the logic object after bus voltage recovery: Per channel: Set the staircase lighting function. 1; Relay: make contact Channel X: Staircase timer Parameter Setting telegram, logic operation Base for staircase timer 100 ms 1 min 1 hr Factor for staircase timer (1-255) - Page 16 Communication objects OR logic operation; Value of logic object after bus voltage recovery: 0; Relay: make contact The following communication objects can be selected: Per channel: telegram, logic operation Function Object name Type Prio Flags Behaviour Channel X Switch object 1 bit Receive Channel X...
-
Page 17: Priority Control
Parameters The function of the priority control after bus voltage recov- ery can be defined by means of a further parameter. The Per channel: Switch on the logic operation. output can be “actuated with priority”, “not actuated with priority” or no active priority can be selected. Channel X: General Parameter Setting... - Page 18 Scenes Per scene: Set the actuator channels. - Scene Scene 1-8 The scene function of the switch actuator has an 8 bit scene Parameter Setting object. Using a parameter, you can define for each scene Channel 1 no change whether the scene should be inactive, active or active with a memory function for new actuator states.
- Page 19 Communication objects The following communication objects can be selected: Per channel: Function Object name Type Prio Flags Behaviour Channel X Status object 1 bit Receive Channel X Status feedback 1 bit Transmit object Parameters Per channel: Switch on the active status response or passive status information.
Need help?
Do you have a question about the KX8O16A and is the answer not in the manual?
Questions and answers