SAFETY INFORMATION WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of Important - Please read these instructions fully before starting assembly fire, electric shock and personal injury including the following. General Power Tool Safety Warnings Read all these instructions before attempting to operate this product and save these instructions".
Page 3
Non-skid footwear is recommended when working outdoors. Wear protective hair covering to contain long hair. 9. Use protective equipment Important - Please read these instructions fully before starting assembly Use safety glasses. General Power Tool Safety Warnings Use face or dust mask if working operations create dust. 10.
Page 4
operate the tool when you are tired. 20. Check damaged parts Before further use of tool, it should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
Page 5
a holder wherever practicable) and rough material; connect the saw to a dust collecting device when sawing wood. In addition the operator shall be informed of factors that influence exposure of dust and the precautions mentioned e.g. type of material to be machined and the importance of local extraction (capture or source) and proper adjustment of hoods/ baffles/chutes;...
Page 6
SYMBOLS To reduce the risk of injury, user must read instruction manual Wear eye protection Wear ear protection Wear dust mask Warning Double insulation Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. EN-6...
TECHNICAL DATA Rated voltage 220-240V~50Hz Rated Input power 1100W No load speed 5500 /min Bevel capacity 0 - 45º Mitre capacity 0-45º L&R Blade size 210 mm Double insulation / II Machine weight 5.2 kg CUTTING CAPACITY: Max cutting mitre/bevel 0°/90° 55*120mm Max cutting mitre/bevel 0°/45°...
Page 12
Vibration Information Vibration total values (triax vector sum) determined according to EN 61029: Cutting wood: a = 4.58m/s Vibration emission value: Uncertainty K = 1.5m/s² The declared vibration total value may be used for comparing one tool with another, and may also be used in a preliminary assessment of exposure.
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. Intended Use This mitre saw is intended for cutting wood and analogue materials ASSEMBLY WARNING:To prevent the accidental starting that could cause possible serious personal injury, ALWAYS assemble all parts to your saw BEFORE connecting it to the power supply. The saw should NEVER be connected to a power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use.
Note: ● Only lift the saw by the operating handle (1) or outer castings. Do not lift the saw using the guards. ● The saw must never be used with the release knob locking the head down. 2. TURNING ON AND OFF THE SAW (SEE FIG. E) Depress and hold the on/off switch trigger (16) to turn on the saw.
5. COMPOUND MITRE CUT When using for cut, user must use a clamping device such as a ‘G" clamp to secure your workpiece. When cutting your workpiece, keep your hands well away from the blade area. Do not remove a cut-off piece on the right-hand side of the blade using your left hand. A compound mitre cut involves using a mitre angle and a bevel angle at the same time.
7. BENCH MOUNTING (SEE FIG. F) Before use, it is recommended to fix the saw to a firm, level surface with 4 mounting bolts (Not supplied). Four holes are provided in the saw base to enable it to be fixed to a bench, or other supporting surface.
MAINTENANCE Remove the plug before carrying out any adjustment, servicing or maintenance. Never use water or chemical cleaners to clean your power tool. Always store your power tool in a dry place. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots.
Page 18
PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE – NEUTRAL BROWN –...
Positec Power Tools (Europe) Ltd, PO Box 6242, Newbury, RG14 9LT, UK Declare that the product Description Mitre Saw Type Designation BMS210 (MS -designation of machinery, representative of Mitre Saw) Function Cutting wood and analog materials Complies with the following Directives: 2006/42/EC, 2011/65/EU, 2014/30/EU...
Need help?
Do you have a question about the BMS210 and is the answer not in the manual?
Questions and answers
Does the saw have an electric cutout