Wall Mounting; Intended Use - DeWalt DCR010 Instruction Manual

English
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the lithium-
ion battery pack on the charger until it is fully charged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115,
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack below +40 °F (+4.5 °C), or above
+104 °F (+40 °C). This is important and will prevent
serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
6
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
DCB118, DCB132
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
COMPONENTS

Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

This D
audio via a wired connection or a wireless Bluetooth®
connection to a mobile phone or other audio device.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the unit.
Supervision is required when inexperienced operators use
this unit.
USB Port (Fig. A)
The USB port (
such as mobile phones, tablets, or portable music players.
When
will charge a device without requiring the user to press the
power button (
When
output port will charge a device when the user presses the
power button (
nOTE: The audio device must connect to the speaker via
Bluetooth®
The USB port is only a power port for charging the audio
device.
Handle/Mobile Phone Cradle
The speaker should be transported using the handle (
handle has a cradle which can be used to hold the mobile
phone while in use.

SAVE THESE INSTRUCTIONS FOR
FUTURE USE
(FIG. A)
WARNING: Never modify the
Damage or personal injury could result.
WALT Bluetooth® speaker is designed to play/stream
e
) delivers up to 2.1 amps to power devices
8
the speaker is powered by the AC cable, the USB port
1 ) .
the speaker is powered by batteries, the USB power
1 ) to turn the speaker on.
or the auxiliary port to use the speaker function.
WARNING: A mobile phone cannot be secured in
the cradle and can fall if the speaker is moved or
transported. Be sure to remove mobile phone from the
cradle before moving or transporting the speaker.
unit or any part of it.
(Fig. D)
) . The
9