7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog HOW TO USE THIS MANUAL This manual contains six sections. The front section contains a table of contents, tables and charts to aid in the identification of vendor models by number and specifications for each. Described below is a brief outline of the numbered sections and the information discussed there.
9. If additional clearance is required, the chandise may then be returned to your lower hinge can be pivoted by remov- Rowe Distributor for repair. The invoice ing the FRONT 1/2" hex head bolt and for repair charges may then be collected loosening the rear bolt one turn.
Page 15
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Adjustable Wall Figure 1-1 Figure 1-2 Adjustable Wall (5-Selection Shelf) Adjustable Wall (10-Selection Shelf) Initial Set-up Procedure bottom of the tray. After adjusting the wall for the desired width, check to Set up the vendor as follows: be certain that the product moves Open the main door all the way.
UBA Bill Acceptor Switch Settings COINCO BA32R #3 OFF, #6 & #8 ON All of the DIP switch settings located on the Rowe UBA assembly circuit board MARS VFM-3 Version 1-3 must be set to the OFF position, except MARS VFM Version 4-5 switch #2, which must be set to the ON position.
Information System (MIS) data. ening the knob. During a purchase, merchandise is A four note Rowe Universal Bill Acceptor moved from the display shelf by a (accepts $1.00, $5.00, $10.00 and rotating helix coil and dispensed into a $20.00 bills) is available as an option.
At that time, the multi-note bill acceptor like the Rowe count is reduced by 1 for each coin dis- RBA-7, the 7800 can be used as a bill pensed until the count reaches 0.
Section 2: Description allows them to be placed at any position Dual helix and pastry shelves (3, 4 or 5 within the machine. A universal shelf can selection) have an adjustable shelf wall be modified to support any combination of located between the last two selections on candy, pastry and dual helixes.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog COIN MECHANISM Install adjustable product guides, if necessary, to accommodate (DOMESTIC) narrow product. A coin mechanism (coin mech) is required to Place product in the appropriate operate this vendor. Refer to page vi or selections.
Page 21
Section 2: Description Because this vendor can operate several coin mech. If coins are loaded through different coin mech models, it is important the top flight deck, the number of coins to ensure that the coin mech installed on is registered by the controller and your vendor is aligned properly with the automatically added to the coin tube coin chute located on the vendor.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Coin Mech Loading Without On all models with a 3, 4, or 5 item shelf, the Cash Accountability first item from the left is 1, the second is 3, Load coins directly into the payout the third is 5, etc.
Section 2: Description Making a Selection next higher number. Allow the system to To make a selection, deposit the proper run twenty (20) minutes before taking amount of money. The display shows another reading. the amount of credit entered. The price Special Vending Modes is displayed beneath each item.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Promotional Vend feature is always enabled. If the discount This feature is intended to free vend a amount is set to zero or greater than the maximum price this feature will have no second item when an item is purchased for effect.
Section 2: Description Explanation of Prioritization “XXXX” is the time the machine will return Assume the following machine configuration: to service. There are 10 programmable events available. An event may be pro- Win-A-Snack - ON grammed to occur on a particular day, Promotional Vend - ON every work day (Monday through Friday), Force Vend - ON...
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog DISPLAY MESSAGE PROMPTS AUDIO FEEDBACK A piezo-type chime mounted on the display “EXACT COINS ONLY” board is sounded for the following events: This message is scrolled when the changer reports that the nickel tube does not contain •...
Section 2: Description will be a maximum of 250 characters in CARD SALES length and will be programmable in the Equals total amount in credit sales vended service mode. This message will not be Range: 0 - $999,999.95 effected by the position of the Language BILLS IN STACKER: (Where applicable) DIP switch.
Rowe 548/648 Showcase Merchandiser, the 550/650 Showcase Merchandiser, and SALES $ 1.00 SALES $ 26.50 the Rowe CD Jukebox. The same printer BAG TOTAL $ 6.00 may now be used to retrieve data from all CASH BOX these machines without changing the printer CARD SALES setup.
Section 3: Program Operation INTRODUCTION Error Messages “OVER CRNT=xx” - This message This section contains detailed instructions indicates motors that have been short on how to program all of the machine's circuited or jammed. features, retrieve MIS information, set prices, and load and calibrate the coin tubes.
Page 30
Section 3: Program Operation SERVICE MODE <8> MIS Display, Printer Communications, and DEX/UCS. OPERATION <9> Programming the Security Code The Service Mode is accessed by either and Security Features pressing the <MODE> button on the control <0> Motor Functions board while the main door is open, or by entering the security code on the keypad.
Page 31
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog KEY 3 X.XX represents the coin value and YY represents the number of coins in IV. KEY 3 - Price, Product Code, the tube. and Discount Eligibility Setting Press <0>...
Section 3: Program Operation KEY 5 that the option is enabled). 10. Choose one of the following appli- VI. Key 5 - Manual Peripheral cable options to view/save price Configuration changes. Purpose: • Press <6> to view the next selection To select the type of credit system used, price.
Page 33
Lplus, Mars MicroMech, and other installed. A serial bill validator must use compatibles) along with either a serial or the Rowe RBA-7 Serial Interface or the pulse type bill validator with or without Mars VFM4 serial interface or equivalent. escrow capability. An MC-5000 compli- A pulse bill validator must output credit on ant card reader is also supported.
Page 34
Section 3: Program Operation Denominations Accepted (ACPT 19. Display responds “BV ESCROW Y” $xx Y/N) or “BV ESCROW N”. This option will allow unconditional rejec- 20. Press <1> to toggle Y/N. tion of specific denominations. This feature 21. Press <5> to save and proceed to the has no effect when using a pulse bill next menu option.
Page 35
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Small Coin Acceptance (SM 6. Press <5> to save the setting and COINS Y/N) proceed to the next menu option. Some MDB coin changers are set up to 7.
Section 3: Program Operation Executive Credit System Pro- gramming Instructions: Display responds with “PRC HLDG Dip switch #4 on the control board must be ON to enable this feature. Y” or “PRC HLDG N”. 2. Press <1> to toggle Y/N. Press <5>...
Page 37
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog 2. Press <3> to get to the ID program- a. Press <9> ming mode. b. Press <0> 3. Use the same control keys used to 3. Press <7> to return to the POS menu. program the POS message and the Press <1>...
Section 3: Program Operation F. Programming the Lockout G. Setting the Date Format Feature Press <7> on the keypad. Press <7> on the keypad. 2. Press <7> again to get to the date 2. Press <6> to get to the lockout format mode.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog triever. The report may be printed, dis- The code number will flash four times. played or sent to DEX/UCS collection 5. The display will read “SECURE OFF/ device. ON”.
Page 40
Section 3: Program Operation The display will read “MOTORS xx” where xx represents the motor status. where xx represents the number of 5. Enter a 2 digit selection. motors detected in the snack machine. As the digits are entered the display Press <RESET>...
Page 41
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog FUNCT?”. 16. Press <5> to save and advance to the next menu option. Press <6> on the keypad. 17. The display will read “A OVR x.xx” 4. The display will read “MTR DE- meaning Automatic Over where x.xx TECT”.
Section 4: Troubleshooting INTRODUCTION • Check to ensure that all plugs are firmly seated in their receptacles. This section contains Troubleshooting • Check to ensure that connector pins Charts, a Block Wiring Diagram, and an are not bent, broken or pushed Interconnect Block Diagram.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog REFRIGERATION above a certain level, the Coil energizes. When the Coil energizes, the normally SYSTEM (OPTIONAL) open contact closes, connecting the Start If the refrigeration system compressor is Capacitor to the Start Winding of the inoperative, perform the following checks motor.
Section 4: Troubleshooting Protective eye wear must be worn when testing refrigeration systems. This system is charged with 6.0 oz. of R134a refrigerant. Repairs should be performed by technicians trained and experienced in refrigeration trouble- shooting and safety procedures. Figure 4-1. Refrigeration System Wiring Diagram 4 - 3 Part No.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Troubleshooting Chart 4-1 Error Messages RROR ESSAGE ROBABLE AUSE OLUTION Shorted or jammed motor “OVER CRNT=” Follow instructions on page 4-3 for locating and replacing defective motors. “HOME FAIL=” Motor did not complete full rotation Follow instructions on page 4-3 for or leave the home position...
Section 4: Troubleshooting Troubleshooting Chart 4-2 Problem/Solution ROBLEM ROBABLE AUSE OLUTION No Indicator lights in machine No AC power into machine Check P1 of Controller 24 VAC @ pins 1 and 2 120 VAC @ pins 4 and 6 Check circuit breaker in transformer assembly.
Page 47
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Troubleshooting Chart 4-2 Problem/Solution ROBLEM ROBABLE AUSE OLUTION Does not register credit Credit message not received from Check for continuity between P2 pin 2 Coin Mech of controller and pin 6 of Coin Mech Socket Coin Mech defective Replace...
Page 48
Section 4: Troubleshooting Troubleshooting Chart 4-2 (Problem/Solution) ROBLEM ROBABLE AUSE OLUTION Two motors run simultaneously Defective Controller Replace Pinched or shorted wires in wire Repair or replace wire harness. harness Fluorescent light does not light Defective lights or starter Replace Cannot buy from row 4 No sale switch ON Set switch to OFF...
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Troubleshooting Chart 4-3 Rowe Bill Acceptor RROR ESSAGE ROBABLE AUSE OLUTION Bill Acceptor rejects a large number of BA STATUS LED flashes once Defective V1 or V4 cell.
Page 50
Section 4: Troubleshooting Troubleshooting Chart 4-3 Rowe Bill Acceptor ROBLEM ROBABLE AUSE OLUTION UBA in SHUTDOWN BA STATUS LED flashes once. Object in Transport covering V1 cell. In this state, the BA Status LED will Defective UBA Unit. flash ON for 1 second and then flash one or more times.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog Interconnect Block Diagram Main Home Switches Coin Mech Controller Door Switch Assembly 67301802002 Bill Printer Validator Display Keypad EXEC/MDB Coin Mech Coin Dispenser Motor Matrix Remote No Sale Switch Transformer Figure 4-2.
Section 5: Maintenance INTRODUCTION Grasp the front of the helix coil and lift straight up. This will release the helix This section contains information on from the helix hub at the rear of the proper cleaning procedures, as well as shelf and the helix will be free in your instructions on how to remove and hand.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog SHELF REMOVAL GUM AND MINT UNIT REMOVAL Shelf removal in the Rowe Snack/Candy Vendor is an easy operation. Remove the 1. Pull out and remove the shelf above shelf as follows: the gum and mint assembly.
Section 5: Maintenance SELECTOR BUTTON HELIX HUB/MOTOR ASSEMBLY REMOVAL REMOVAL The selector button assembly in the snack 1. Turn the power OFF. vendor is a sturdy, reliable assembly 2. Slide the shelf forward, lift the shelf developed and constantly improved over upward and out.
7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog UNIVERSAL SHELF e. Rotate the motor 90 clockwise. CONVERSION f. Reinstall the motor assembly to the right most slot opening. Converting from a Dual Helix to a g. Reinstall the helix hub by positioning Single Helix selection.
All parts must be ordered from an authorized Rowe Distributors. Each list contains an index of the part, Distributor. Parts orders are often delayed because Rowe Part Number, a description of the part and the of inadequate or incomplete ordering information. quantity required for the assembly. Separate parts...
Page 67
7800 Deluxe Snack / Candy OPTIONAL KITS 7800 7800JR 7800C DESCRIPTION FUNCTION Part No. Part No. Part No. 42506037 " " UBA Bill Acceptor kit Allows currency acceptance 49001925 " " Product Pusher Kit Pushes product out 49004501 " " Shelf Extender Cable Assembly Service shelf outside of cabinet 49006007...
Page 68
7800 Deluxe Snack / Candy PARTS CATALOG Table of Contents FlG. NO. TITLE PAGE Main Door Trim and Panels 7 - 4 Main Door Exterior 7 - 6 Main Door Interior 7 - 8 Delivery Box Assembly 7 - 10 Cabinet Assembly Components 7 - 12 Power Panel Components...
7800 Deluxe Snack / Candy Fig. 2 Main Door Exterior 900-68702...
Page 72
7800 Deluxe Snack / Candy Fig. 2 Main Door Exterior Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 67301400 67401400 67101400 Door F/A 67301401 67401401 67101401 Door Weld Assembly 40800511 Same Same Cap - Top Trim 58300404 "...
7800 Deluxe Snack / Candy Fig. 3 Main Door Interior 900-68702...
Page 74
7800 Deluxe Snack / Candy Fig. 3 Main Door Interior Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 67301400 67401400 67101400 Door F/A 67301401 67401401 67101401 Door Weld Assembly 67301801 67401800 67101800 Lamp Bracket Assy 70080003 70080001 70080001...
Page 82
7800 Deluxe Snack / Candy Fig. 6 Power Panel Components Quantity Rowe Part Description Index Assembly Number Number 67301803 Power Supply F/A 120V 60Hz 67301804 Power Supply F/A 220V 50Hz 67301805 Power Supply F/A 240V 50Hz 58301600 Power Box Assembly (Export)
7800 Deluxe Snack / Candy Fig. 7 Shelf Support and Plug Assemblies 7-18 900-68702...
Page 84
7800 Deluxe Snack / Candy Fig. 7 Shelf Support and Plug Assemblies Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 59301824 Same Same Plug Bracket W/A 59300805 " " Plug Bracket 44802480 " " Step Washer 97901253 "...
Page 86
7800 Deluxe Snack / Candy Fig. 8 3, 4, or 5 Selection Shelf Assembly Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 59301615 59401615 59101615 Shelf W/A 59301605 59401604 59101603 Shelf Assembly - 3/4/5 Select 59301617 Same Same...
Page 90
7800 Deluxe Snack / Candy Fig. 10 Candy Shelf Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 59301615 59401615 59101615 Shelf W/A 59301610 59401608 59101606 Shelf Assembly - Candy 6/8/10 Select 49300016 " " Candy Helix - 10 Select 10/8/6 49300015 "...
Page 91
7800 Deluxe Snack / Candy Fig. 11 Gum and Mint Unit 7-26 900-68702...
Page 92
7800 Deluxe Snack / Candy Fig. 11 Gum and Mint Unit Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 59301715 59401715 59101700 Gum and Mint Final Assembly 59301710 59401710 59101701 Gum and Mint Weld Assembly 59300726-239 59400726-239 59100700-239 Cover Gum and Mint Unit 59300725-239 59400725-239 59100706-239...
Page 94
7800 Deluxe Snack / Candy Fig.12 Refrigeration Unit (Optional) Index 7800 7800JR 7800C Quantity Part Part Part Description Number Number Number Assembly 58301201 58322501 Condensing Unit 58322502 Same Cover-Condensing Unit 58322504 " " Tubing Suction 58322505 " " Tubing Condenser Out 58322516 "...
Page 96
7800 Deluxe Snack / Candy Fig.13 Main Controller Circuit Board Assembly Reference Part Type Value Part Num. CAPACITOR - ELECTROLYTIC 22µF 25 VDC 20% 203A7D6100-2206 CAPACITOR - ELECTROLYTIC 22µF 25 VDC 20% 203A7D6100-2206 CAPACITOR - ELECTROLYTIC 22µF 25 VDC 20% 203A7D6100-2206 MONOLYTHIC CERAMIC470pF 50 VDC 10%...
Page 97
7800 Deluxe Snack / Candy Fig.13 Main Controller Circuit Board Assy Cont. Reference Part Type Value Part Num. NOT USED HEADER 3 POSITION .100 STRAIGHT 70078703 HEADER 3 POSITION .100 STRAIGHT 70078703 HEADER 3 POSITION .100 STRAIGHT 70078703 HEADER 3 POSITION .100 STRAIGHT 70078703 INDUCTOR 3 AMP 200µH...
Page 98
7800 Deluxe Snack / Candy Fig.13 Main Controller Circuit Board Assy Cont. Reference Part Type Value Part Num. RESISTOR - CARBON FILM 1/8W 5% 79905203 RESISTOR - CARBON FILM 1/8W 5% 79905823 RESISTOR - CARBON FILM 1/8W 5% 79905203 RESISTOR - CARBON FILM 1/8W 5% 79905823 RESISTOR - CARBON FILM...
Page 99
7800 Deluxe Snack / Candy Fig.13 Main Controller Circuit Board Assy Cont. Reference Part Type Value Part Num. RESISTOR - CARBON FILM 4.7K 1/4W 5% 79901479 RESISTOR - CARBON FILM 1/8W 5% 79905102 RESISTOR - CARBON FILM 1/8W 5% 79905202 RESISTOR - CARBON FILM 6.2K 1/8W 5%...
Page 100
7800 Deluxe Snack / Candy Fig.13 This page intentionally left blank. 900-68702 7-35...
7800 Deluxe Snack / Candy Fig.17 Harness List 58301800 Harness, Main Cabinet 58301829 Harness, Main Door - 6800 Deluxe 58301827 Harness, Keypad - 6800 Deluxe 58301830 Harness, Coin Mech-Domestic 58301826 Harness, CBA/UBA Data - 6800 Deluxe 58301832 Harness, Exec Mech Data - 6800 Deluxe 58301828 Harness, Door-Power - Dom.
Page 108
Section 6: TROUBLESHOOTING & SELF-DIAGNOSTICS MISCELLANEOUS PROBLEMS The following problems may occur in the Bill Changer without causing a fault code. ERRATIC PAYOUT Problem: The changer is not consistently dispensing the correct number of coins. Symptom: One vend is short a coin. The next vend contains an extra coin. Corrective Action: 1.
Page 109
Century Series Bill Changer COIN COUNTING PHOTOTRANSISTOR (SENSOR) CHECK Use the following procedure to check the phototransistor (sensor) in the dispenser coin detector system: 1. Switch the Bill Changer power OFF at the electrical box. 2. Remove the black plastic cover from the phototransistor and connect a common meter lead to the metal dispenser backing plate as shown in Figure 6-1.
Page 110
Section 6: TROUBLESHOOTING & SELF-DIAGNOSTICS LOW COIN SENSOR ELECTRICAL CHECK Perform the following procedure to ensure that the Low Coin Sensor is functioning properly. 1. Turn the Bill Changer power to OFF. 2. Remove the hopper and empty it of all coins. WARNING: Make sure that the power is OFF before performing the following step.
Need help?
Do you have a question about the 7800 Deluxe Series and is the answer not in the manual?
Questions and answers