Advertisement
Quick Links
Congratulation on your purchase of the RF(Radio Frequency) wireless Chalkboard.
By using the advanced RF technology, a 360° of operation is possible, and no line-of-sight is required between the
receiver and the chalkboard. The chalkboard, with the high performance and long distance, will bring users the best
operation accuracy and efficiency.
This guide will help you to install the device driver and PenSuite™ utilities, and also contains tips on using a
chalkboard as well as solutions to common problems. See the user's manuals on the Driver and PenSuite CD for more
detailed instructions. To install the chalkboard you will need:
(1) Connect the hardware to the PC,
(2) Install the driver and pen utilities software, and
(3) Verify that the chalkboard functions correctly.
(1) Connecting the receiver with USB interface to the PC:
Please insert the USB connector into an available USB port on the PC according to the diagram below). After
detecting the receiver, the system will start to install the device driver.
(2) Setting up the correct channel for both the receiver and the chalkboard:
The RF wireless chalkboard provides 78 different RF channels, and 18 identification codes to avoid interference
with other radio devices or other same model of RF wireless chalkboard.
Before you using the wireless chalkboard, please set the same carrier frequency and ID channels for both receiver
and chalkboard.
Please follow the procedures to set up:
1. Installing the batteries
This RF wireless chalkboard uses 2 AA batteries.
To apply the batteries, please follow the following steps:
1. Flip the chalkboard upside down and remove the battery cover by the opening tab.
2. There are signs to indicate the polarity of the batteries. Carefully follow the signs to place the batteries.
3. Place the battery cover back and make sure it is firmly closed.
V.1.00 Mar/1/2005
C
HALKBOARD
UCW2000
U S E R ' S M E N U A L
OV ERV I EW
GETTING STARTED
CONN EC TIN G TH E HARD WAR E TO TH E PC
Figure 1 Connecting a chalkboard with USB Interface to a PC
1
95E-0000-003
Advertisement
Summary of Contents for Abocom UCW2000
- Page 1 HALKBOARD UCW2000 U S E R ’ S M E N U A L OV ERV I EW Congratulation on your purchase of the RF(Radio Frequency) wireless Chalkboard. By using the advanced RF technology, a 360° of operation is possible, and no line-of-sight is required between the receiver and the chalkboard.
- Page 2 HALKBOARD UCW2000 Battery Warning! When replace the batteries, use rechargeable. You may use other heavy duty NiMH or alkaline batteries, but do not mix them with each other. Do not mix used old and new batteries together! 2. Establishing communication between the receiver and the chalkboard 1.
- Page 3 HALKBOARD UCW2000 V ERI FYING INS TA LLATION To ensure that everything has been installed properly, please follow the procedure described below. The user's manual on the install CD gives full instructions and also provides more suggestions for dealing with unexpected conditions.
-
Page 4: Usage Tips
HALKBOARD UCW2000 Figure 3: Chalkboard control panel (left, the image you see may be different) and pressure configuration page (right) (2) To verify the function, select the Pressure tab and try to draw a few lines in the Pressure Test area. -
Page 5: Common Problems And Solutions
HALKBOARD UCW2000 After you use pen scrolling without tapping for some time, you may find the pen to suddenly stop functioning. Just tap on any surface to “wake up” the pen out of standby mode. OLDING THE ERTICALLY When drawing pictures or signing your name, try to hold the pen vertically for best results. - Page 6 HALKBOARD UCW2000 Consult the dealer or an experienced radio/TV technician for help. (15.21) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 15.19 (a)(3) This device complies with Part 15 of the FCC Rules.