Advertisement
Quick Links
PEMBRIDGE
IMPORTANT NOTE: ENSURE THAT ALL RELEVANT PERSONNEL READ THESE INSTRUCTIONS PRIOR TO USE
Please also refer to the 'Manual Handling Operations Regulations 1992' during the handling of the product
and materials used for installation. Glasdon recommends that a full Health and Safety analysis is carried out
WHEELCHAIR ACCESS MODEL
KIT CONTENTS:
ITEM 1 - Crossbar and Leg Assembly
ITEM 2 - Seat Assembly
ITEM 3 - Support Blocks
ITEM 4 - Coach Bolt - M10 x 180mm
ITEM 5 - Washer - M12 x Ø23mm
ITEM 6 - Nyloc Nut - M10
ITEM 7 - Domed Tamper Resistant Cover Cap
ITEM 8 - Tamper Resistant Cover Cap
ITEM 9 - Hex Head Bolt - M10 x 130mm
PICNIC
™
INSTRUCTIONS MANUAL
prior to installation.
x 1
x 2
x 4
x 2
x 10
x 10
x 4
x 8
x 8
Table Pack
TABLE
EQUIPMENT REQUIRED:
- Cordless Drill or Philips Screwdriver
- 17mm Socket Wrench
- Mallet
3
2
1
x 1
x 2
x 1
4
8
9
5
6
7
Advertisement
Related Manuals for Glasdon PEMBRIDGE
Summary of Contents for Glasdon PEMBRIDGE
- Page 1 IMPORTANT NOTE: ENSURE THAT ALL RELEVANT PERSONNEL READ THESE INSTRUCTIONS PRIOR TO USE Please also refer to the ‘Manual Handling Operations Regulations 1992’ during the handling of the product and materials used for installation. Glasdon recommends that a full Health and Safety analysis is carried out prior to installation.
- Page 2 ASSEMBLY INSTRUCTIONS 1. Carefully remove packaging from the table and pallet. 2. Using the hand drill or screwdriver unscrew the fixings holding the timber blocks supporting the seat assemblies during transit. Remove the 2 x wingnuts holding the table legs to the pallet. 2 of 12...
- Page 3 3. Carefully remove the crossbar and leg assembly (Item 1), seat assemblies (Item 2), support blocks (Item 3) and fixing pack from the pallet. IMPORTANT : If manually moving the table pack we strongly recommend that for the Enviropol® model a minimum of five people manoeuvre the table into position.
- Page 4 5. Place 4 x support blocks (Item 3) between the fitted crossbar and the ground directly beneath the halving joint. 6. Feed the crossbar and leg assembly (Item 1) through the table pack assembly and slot it into the corresponding halving joints of the fitted lower crossbar. Take care to orientate the crossbar and leg assembly the correctly with the halving joints facing the downward.
- Page 5 7. Ensure the crossbars are fully engaged by gently tapping the crossbar and leg assembly down with the mallet directly above the support blocks until the tops of the crossbars are level. 8. Pivot the legs downward from the crossbar and leg assembly. Align the fixing holes between the top of the leg and the underside of the table top frame by tapping the base of each leg with the mallet until they line up.
- Page 6 9. Insert the M10 x 180mm coach bolt (Item 4) through the table top support and the tops of the legs. Take care to insert the fixing through the small hole and not the larger counter bore hole. Secure with a washer (Item 5) and nyloc nut (Item 6).
- Page 7 11. Insert 4 x M10 x 130mm bolts (Item 9) through the seat and crossbar (mallet may be required). Secure in position using the washer (Item 5) and nyloc nuts (Item 6). Use 2 x 17mm socket wrenches to tighten all fixings.
- Page 8 INSTALLATION INSTRUCTIONS KIT CONTENTS: ITEM 10 - Self Tapping Anchor Bolt - M10 x 100mm ITEM 11 - Washer - M12 x 23mm EQUIPMENT REQUIRED: - Rotary Hammer Drill - 10mm Masonry Drill Bit - 17mm Socket Wrench - Dust Blower/Hard Bristle Brush MINIMUM BASE REQUIREMENT If no suitable existing base, then base to be sized as per dimensions below with 200mm thickness of concrete onto well consolidated hardcore.
- Page 9 VIEW B 1345mm Fixing Centres 1800mm Overall Table Dimensions 2000mm Concrete Base For optimum fixing performance the following procedure is recommended. The base should be flat, steel float finished, level and square and preferably be raised slightly above the surrounding ground level. The concrete base should be a minimum 25N/20mm mix strength equivalent of BS.
- Page 10 BLANK PAGE 10 of 12...
- Page 11 BLANK PAGE 11 of 12...
- Page 12 GIVEN TO STAFF INVOLVED WITH THE INSTALLATION AND MAINTENANCE OF THIS PRODUCT. SAFETY NOTE: PLEASE REFER TO ‘THE MANUAL HANDLING OPERATIONS REGULATIONS 1992’ DURING HANDLING. AND PEMBRIDGE ARE TRADEMARKS OR REGISTERED TRADEMARKS OF GLASDON GROUP OR ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES A planned maintenance schedule or regular inspection is recommended, replacing components as necessary.
Need help?
Do you have a question about the PEMBRIDGE and is the answer not in the manual?
Questions and answers