1. Manuals
  2. Brands
  3. EOM Manuals
  4. Water Pump
  5. T1 Original Metal Series
  6. Manual

EOM T1 Original Metal Series Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
T1
™
Original
Series METAL Pumps
S i m p l i f y y o u r p r o c e s s
E n g i n e e r i n g
O p e r a t i o n &
M a i n t e n a n c e
WIL-10190-E-03
WIL-10190-E-03
REPLACES WIL-10190-E-02
C S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T1 Original Metal Series and is the answer not in the manual?

Questions and answers

Related Manuals for EOM T1 Original Metal Series

Summary of Contents for EOM T1 Original Metal Series

  • Page 1 E n g i n e e r i n g O p e r a t i o n & ™ Original Series METAL Pumps M a i n t e n a n c e S i m p l i f y y o u r p r o c e s s WIL-10190-E-03 WIL-10190-E-03 REPLACES WIL-10190-E-02...

  • Page 2: Table Of Contents

    T A B L E O F C O N T E N T S SECTION 1 CAUTIONS—READ FIRST! ..........1 SECTION 2 WILDEN PUMP DESIGNATION SYSTEM .

  • Page 3: Cautions-Read First

    S e c t i o n 1 C A U T I O N S — R E A D F I R S T ! TEMPERATURE LIMITS: CAUTION: Before any maintenance or repair is Nylon –17.8°C to 93.3°C 0°F to 200°F attempted, the compressed air line to the pump should Neoprene...
  • Page 4 S e c t i o n 2 P U M P D E S I G N A T I O N S Y S T E M T1 ORIGINAL™ LEGEND T1 / X X X X X / XXX / XX / X XX / XXXX METAL O-RINGS...
  • Page 5 S e c t i o n 3 H O W I T W O R K S — P U M P D I S T R I B U T I O N S Y S T E M The Wilden diaphragm pump is an air-operated, positive displacement, self-priming pump.

  • Page 6: Dimensional Drawings

    S e c t i o n 4 D I M E N S I O N A L D R A W I N G 13 mm DIMENSIONS (1/2”) FNPT LIQUID DISCHARGE ITEM METRIC (mm) STANDARD (inch) E - ALUM. D - S.S.

  • Page 7: Rubber-Fitted

    S e c t i o n 5 A P E R F O R M A N C E T1 METAL RUBBER-FITTED Height ........224 mm (8.8") Width ........208 mm (8.2") Depth ........178 mm (7.0") Est. Ship Weight ..Aluminum 6 kg (13 lbs) Stainless Steel 9 kg (20 lbs) Air Inlet ........

  • Page 8: Ptfe-Fitted

    S e c t i o n 5 A P E R F O R M A N C E T1 METAL PTFE-FITTED Height ........224 mm (8.8") Width ........208 mm (8.2") Depth ........178 mm (7.0") Est. Ship Weight ..Aluminum 6 kg (13 lbs) Stainless Steel 9 kg (20 lbs) Air Inlet ........

  • Page 9: Suction Lift Curves

    S e c t i o n 5 B S U C T I O N L I F T C U R V E T 1 M E T A L S U C T I O N L I F T C A P A B I L I T Y Suction lift curves are calibrated for pumps operating at 305 m (1,000’) above sea level.
  • Page 10 S e c t i o n 6 S U G G E S T E D I N S T A L L A T I O N The Model T1 Metal pump has a 13 mm (1/2") inlet and The best choice possible will be a site involving the shortest 13 mm (1/2") outlet and is designed for flows to 54.9 lpm and the straightest hook-up of suction and discharge piping.
  • Page 11 S e c t i o n 5 A S U G G E S T E D I N S T A L L A T I O N ® NOTE: In the event of a power failure, the shutoff valve should be closed, if the restarting of the pump is not desirable once power is regained.
  • Page 12 S e c t i o n 6 T R O U B L E S H O O T I N G Check to make sure all suction connections are air tight, Pump will not run or runs slowly. especially clamp bands around intake balls.
  • Page 13 S e c t i o n 7 P U M P D I S A S S E M B L Y CAUTION: Before any maintenance or repair is attempted, the compressed air line to the pump should be discon- nected and all air pressure allowed to bleed from the pump.
  • Page 14 S e c t i o n 6 P U M P D I S A S S E M B L Y Step 4. Step 5. Figure 4 Figure 5 Inspect the ball retainer, retainer o-ring, and valve Remove the discharge valve balls, seats and o-rings ball from intake manifold.
  • Page 15 S e c t i o n 6 P U M P D I S A S S E M B L Y Step 9. Step 10. Figure 9 Figure 10 Lift the liquid chamber away from the center section to Using an adjustable wrench, or by rotating the expose the diaphragm and outer piston.

  • Page 16: Assembly / Disassembly

    S e c t i o n 6 A I R V A L V E / C E N T E R S E C T I O N R E P A I R / M A I N T . The center section assembly consists of both the air valve body and piston and the center section.

  • Page 17: Reassembly Hints & Tips

    S e c t i o n 6 R E A S S E M B L Y H I N T S & T I P S ASSEMBLY: Upon performing applicable maintenance to the air distribution system, the pump can now be reassembled. Please refer to the disassembly instructions for photos and parts placement.

  • Page 18: Exploded View And Parts Listing

    S e c t i o n 8 E X P L O D E D V I E W & P A R T S L I S T I N G T1 METAL R u b b e r / T P E - F i t t e d E X P L O D E D V I E W WILDEN PUMP &...
  • Page 19 S e c t i o n 6 E X P L O D E D V I E W & P A R T S L I S T I N G T1 METAL R u b b e r / T P E - F i t t e d P A R T S L I S T I N G Rubber-Fitted Qty.

  • Page 20: T1 Metal Ptfe-Fitted

    S e c t i o n 8 E X P L O D E D V I E W & P A R T S L I S T I N G T1 METAL P T F E - F i t t e d E X P L O D E D V I E W NOTE: PTFE Diaphragm Models Assembled with PTFE Gasket Kit At Factory (Not Shown)
  • Page 21 S e c t i o n 6 E X P L O D E D V I E W & P A R T S L I S T I N G T1 METAL P T F E - F i t t e d P A R T S L I S T I N G Qty.

  • Page 22: Elastomer Options

    S e c t i o n 9 E L A S T O M E R O P T I O N S T1 Metal Pumps Material Diaphragm P/N Valve Ball P/N Valve Seat P/N Valve Seat O-Ring P/N Manifold O-Ring P/N Polyurethane 01-1010-50...
  • Page 23 W A R R A N T Y Each and every product manufactured by Wilden Pump and Engineering, LLC is built to meet the highest standards of quality. Every pump is functionally tested to insure integrity of operation. Wilden Pump and Engineering, LLC warrants that pumps, accessories and parts manufactured or supplied by it to be free from defects in material and workmanship for a period of five (5) years from date of installation or six (6) years from date of manufacture, whichever comes first.

Table of Contents