Advertisement
Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St,
Revesby, NSW. 2212
www.furnituresolutions.com.au
Please retain these pages as they contain tips to maximize the lifetime of your furniture with a measured effort.
Properly caring for your furniture can help ensure that it looks great year after year.
Important Notice: While every effort is made to use quality materials our products are limited in design for domestic use only
& are not suitable for commercial use.
Piazza 2Pce Modular Lounge
Piazza Low Dining Table
Piazza Bench Seat
(Sold Separately Assembly Required)
(Sold Separately Assembly Required)
INSTRUCTION MANUAL
PRODUCT: PIAZZA RANGE
MADE IN CHINA
Advertisement
Table of Contents
Related Manuals for Furniture Solutions Piazza Series
Summary of Contents for Furniture Solutions Piazza Series
- Page 1 INSTRUCTION MANUAL PRODUCT: PIAZZA RANGE Furniture Solutions (Aust) Pty Ltd MADE IN CHINA 10-16 Daisy St, Revesby, NSW. 2212 www.furnituresolutions.com.au Please retain these pages as they contain tips to maximize the lifetime of your furniture with a measured effort. Properly caring for your furniture can help ensure that it looks great year after year.
-
Page 2: Pre Assembly Preparation
Do not over tighten the screws and bolts as this may damage the threads MINUTES ALLOW TIME PEOPLE REQUIRED For any assistance with assembly or missing parts please contact: Place of purchase or Furniture Solutions on below Customer Service (Australia) Phone– 1300794 188 Email– customerservice@furnituresolutions.com.au... - Page 3 Component List Piazza 2Pce Modular Sofa with corner 2100*850*680mm Frame Size 1940*780*120mm Seat Cushion x 1 640*420*300mm Back Cushion x 3 540*420*300mm Corner Cushion x 1 Sofa one end open 2120*850*680mm 1940*780*120mm Seat Cushion x 1 640*420*300mm Back Cushion x 3 Scatter Cushion x 6 450*450mm...
- Page 4 Component List Low Dining Table Component List Bench Seat A: x 1 A: x 1 Table Top Bench Top 165*98cm 150*40cm B: x 2 B: x 2 Table Leg Bench Leg C: x 1 C: x 1 Support Brace Support Brace Parts List Low Dining Table Parts List Bench Seat D: x 12...
- Page 5 Piazza Low Dining Table ASSEMBLY STEP 2– FIT SUPPORT BRACE Take support brace [C] with the help of another person line up holes in support brace with threaded holes in table leg, as indicated in diagram. With other person holding support brace level.
- Page 6 Piazza Bench Seat ASSEMBLY STEP 1/2– FIT LEG FRAME Lay bench top [A] facing down on a soft clean surface. Locate threaded holes inside of frame in bench top. With the help of another person aline the holes in bench leg [B] with thread holes in table top.
-
Page 7: Product Care And Maintenance
2/3 water using a soft non-metallic brush, please rinse thoroughly with clean water and dry as above. Some scratchers and marks can be sanded out depending on surface of Polywood please contact Furniture Solutions before attempting to repair, contact details on page 2. Fabric Information Fabrics used in outdoor product are not made of any special type of material;... - Page 8 PRODUCT CARE & MAINTENANCE Aluminium Frame Information The majority of frames are mainly produced from aluminium, with the main benefit being a light weight product for easier use. Some designs require steel to be used in certain sections for added strength. While aluminium is rust resistant, bare metal can show signs of oxidation (red film) this does not constitute rust.
- Page 9 WARNING SAFETY & ADVICE Please be aware materials used in your furniture are not impervious to neglect, acts of god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based product, products are limited in design for residential use only and not suitable for commercial use. Please be aware that heat generated from barbeques and heaters will have an adverse effect on your furniture do not place furniture in close proximity to heat sources.
-
Page 10: Warranty Details
Extended Warranty of (2) year total of (3) years applies to aluminum frame against any defect associated with faulty workmanship from date of purchase. Furniture Solutions accepts no responsibility for defects caused by incorrect assembly, mishandling, acts of god, general wear & tear, stains from spills/vegetation, chipping/scratching, exposure to extreme heat/cold, mould/ mildew, hardware corrosion, misuse of the products &...
Need help?
Do you have a question about the Piazza Series and is the answer not in the manual?
Questions and answers