Summary of Contents for ZIVE LAB ZIVE SP2
- Page 1 ZIVE SP2 Electrochemical Workstation Hardware Manual sales@wonatech.com service@wonatech.com W. www.zivelab.com © 1991–2015 ZiveLab. All rights reserved. Copyright○ 2011 ZiveLab. Revision 6502 May, 2015...
- Page 2 Instrument Certificate Date: Model : ZIVE SP2 Serial No.: End-user: AC Power Line: 100VAC-240VAC 50/60Hz Installation date: Warranty Period: One Year Option V range I range +/-10V Corrosion +/-1V 200mA ElectroAnalysis +/-100mV 20mA Battery 200uA 20uA 200nA 20nA 200pA 20pA...
- Page 3 ZIVE SP2 Instruction manual - 3 -...
- Page 4 ZIVE SP2 Instruction manual This manual has to be read carefully before switching on the instrument. The Instructions must be followed strictly. Non-observance of these instructions can lead to the loss of right to claim for damages or guarantee. Manufactured by WonATech Co,.
- Page 5 ZIVE SP2 Instruction manual Take the time to read this License Agreement prior to opening this package, because by opening the package, you accept the terms and conditions of this License Agreement. Likewise, if you do not accept the terms of this agreement, do not open this package.
- Page 6 ZIVE SP2 Instruction manual Limited Warranty WonATech warrants to the original user of this product that it shall be free of defects resulting from faulty manufacture of the product or its components for a period of one year from the date of shipment.
-
Page 7: Table Of Contents
USB port ..................................13 Optional Software package License ....................... 13 CE compliance ................................. 13 Chapter 3. Reference ......................14 ZIVE SP2 block diagram ............................15 For single channel configuration ........................ 15 For Multichannel Configuration ........................15 Chapter4. Installation ......................16 Rear Panel.................................. - Page 8 ZEN-IV board ................................33 Booster board ................................34 USB interface board .............................. 34 Front board (Single channel; ZIVE SP2) ......................36 Inter-connecting boards (Single channel; ZIVE SP2) ................36 Appendix 3. Cables & Dummy cell ..................37 Cell cable ................................... 37 Aux cable ...................................
- Page 9 ZIVE SP2 Instruction manual Appendix 4. Front Panel Connectors .................. 43 Aux connector ................................43 Misc connector ................................ 43 Cell Connector ................................. 44 Appendix 5 : CE certificate ....................45 Declaration of conformity ........................... 45 EMC test report ............................... 46...
-
Page 10: Chapter 1. Pre Startup Checking Points
Do not place any obstacle preventing air flow at bottom or the side of the unit ZIVE SP2 should only be used with the supplied cell cable. If you use a custom made cell cable, it is likely to create noisy data. -
Page 11: Software Upgrade And General Information
ZIVE SP2 Instruction manual A service contract that extends the hardware warranty is available at an additional charge. Please contact your local representative or distributor. 4. Software upgrade and general information The latest version of firmware and software upgrade is available at http://www.zivelab.com. -
Page 12: Chapter 2. General Instruction
Failure to do so may create a safety hazard. 2. Safety You must use earth grounded AC power source. You should use AC/DC adapter which supplied with ZIVE SP2. Do not use other power source other than that supplied with the ZIVE SP2. - 12 -... -
Page 13: Usb Port
ZIVE SP2 Instruction manual There is screw part on power connector, you must connect adapter’s screw cap to this screw part. Do not locate any obstacles which will prevent air flow at bottom and side of the ZIVE SP2. 3. USB port PC must have usb2.0 high speed port and needs USB port number per device... -
Page 14: Chapter 3. Reference
ZIVE SP2 Instruction manual Chapter 3. Reference ZIVE SP2 generates sine wave using fast DAC(50MHz) with DDS and DSP calculate the impedance in accordance with the block diagram below. Output signal has x1, x0.1 and x0.01 gain. Current & voltage input signal has x1, x10 and x100 gain. -
Page 15: Zive Sp2 Block Diagram
ZIVE SP2 Instruction manual 1. ZIVE SP2 block diagram A. For single channel configuration B. For Multichannel Configuration - 15 -... -
Page 16: Chapter4. Installation
ZIVE SP2 Instruction manual Chapter4. Installation 1. Rear Panel Internal FRA included FPGA/DSP control Plug-In Type Busy LED communication Power switch RUN LED Temperature measurement (K type) LAN port thermocouple (option) USB port Cell port : Working, reference, counter, working sense, ground Power connector Misc. -
Page 17: Front View
ZIVE SP2 Instruction manual 2. Front view Air flowing holes - 17 -... -
Page 18: Front Panel Lcd
ZIVE SP2 Instruction manual 3. Front panel LCD There is a front panel LCD that displays relevent test information. Its function will be automatically change depending on the applied test mode (impedance test or DC test). Asteristic or heart mark: blinking １) DC data monitoring... -
Page 19: Ac Data Monitoring
Current range 4. Checking points Power line cables (PC, Monitor, Zive SP2, Printer etc.) should be for earth ground No fault on system information of Windows 2000/XP/Vista/7/8 control panel No virus in Software inside PC Test ZIVE SP2 using dummy cell. -
Page 20: Software
, it means that communication between PC and ZIVE SP2 is disconnected. ZIVE SP2 can save the data file in PC in real time but for fast sampling rate(including burst mode), data stocking speed in ZIVE SP2 is faster than transfer rate to PC. So after finishing the experiment, data transferring from ZIVE SP2 to PC may continue for some time. -
Page 21: Device Utility
Each channel is plug and play type. Easy firmware upgrade It is possible to extend multichannel system using several set of ZIVE SP2 using USB hub. If there is PC power failure or USB cable is unplugged by accident, the experiment keeps going and you can tranfer data from ZIVE SP2 memory any time. -
Page 22: Channel Expansion
ZIVE SP2 Instruction manual If you input wrong license code, you can see the following message You MUST click “Save channel info”. After above process, you MUST turn off ZIVE SP and turn it on. License code comes from ZIVE SP serial number. So if you try to input license code for other ZIVE ... - Page 23 ZIVE SP2 Instruction manual Click Device utility icon on tool bar Select device number on channel 2 Click “Save Ch. Setting” button Multichannel system is ready. Note: If each SP has different license, each license will work only for its SP.
-
Page 24: Chapter5. Update Firmware
ZIVE SP2 Instruction manual Chapter5. Update firmware When you install new version smart manager software, this software will detect firmware update requirement. If it require firmware update, you can update firmware package in smart manager software. Please refer to Smart Manager operation manual. -
Page 25: Usb Firmware Update
If the progress bar stops, it is mainly due to lack of resources in the computer. Close other application programs and turn-off /turn on the instrument and try to update firmware again. Do not turn off during firmware upgrade. After Firmware upgrade, you must turn off ZIVE SP2 and turn it on If PC was not connected to instruments, the following message will be displayed.. -
Page 26: Fpga Firmware Update
ZIVE SP2 Instruction manual Click “Select firmware file “button and select firmware package(*.sfw), the you can see file information at “ USB firmware” at bottom side. The information of “Chip Information” section is for firmware information inside of instruments. Please compare with two dates and only if target firmware’s date is newer, try to update the firmware. -
Page 27: Dsp Firmware Update
ZIVE SP2 Instruction manual C. DSP firmware update To update dsp firmware; Select channel number. Click “Select firmware file “button as the above and select firmware package(*.sfw), the you can see file information at “ file information” at bottom side. The information of “Chip Information” section is for firmware information inside of instruments. -
Page 28: Chapter 6. Cell Connection
Reference: White connector Counter: Red connector ZIVE SP2 was shipped with standard 1meter shielded cell cable. Cell connector is Dsub type and other side has 5 banana ended plugs with removable alligator clips. 25pin Dsub male connector of standard cell cable connects to SP2’s rear panel 25pin Dsub female connector. -
Page 29: General Connection (3 Electrodes Connection)
ZIVE SP2 Instruction manual 1. General connection (3 electrodes connection) Red colored lead to counter electrode White colored lead to reference electrode Green colored lead to working electrode Blue colored lead to working electrode Working Counter:... -
Page 30: Zra Connection (2 Working Electrodes Connection)
ZIVE SP2 Instruction manual 3. ZRA connection (2 working electrodes connection) AuxV1(-) lead to reference electrode Green colored lead to working1 electrode Blue colored lead to working1 electrode AuxV1(+) lead to working1 electrode White colored lead : Working2 electrode ... -
Page 31: Appendix 1. Specification
ZIVE SP2 Instruction manual Appendix 1. Specification Main system PC communication USB2.0 High Speed Line voltage 100-240VAC, 50/60Hz, 1Amp Power adapter 24V@2.5A Size/weight 113X305.7X196mm(W*D*H) / 3.2kg Max output power 24Watt System Cell cable 1meter shielded type (Standard) Working, reference, counter,... - Page 32 ZIVE SP2 Instruction manual Electrometer Max input voltage ±10V Input impedance 2x10 Ω||4.5pF Bandwidth >22MHz CMRR >114dB EIS(Internal FRA) for system Frequency range 10uHz ~ 2MHz Frequency accuracy 0.01% Frequency resolution 5000/decade Amplitude 0.1mV ~ 5V rms (Potentiostatic) 0.1 ~ 70%(Galvanostatic)
-
Page 33: Appendix 2. Boards
ZIVE SP2 Instruction manual Appendix 2. Boards 1. Main board -connecting board Inter connector ZenIV board connector Inter-connecting board 2. ZEN-IV board connector - 33 -... -
Page 34: Booster Board
ZIVE SP2 Instruction manual 3. Booster board Inter-connecting board connector Inter-connecting board connector 4. USB interface board ROM Switch - 34 -... - Page 35 ZIVE SP2 Instruction manual Power switch USB port ROM switch Power connector ROM switch direction: write enable ROM switch direction: write protected - 35 -...
-
Page 36: Front Board (Single Channel; Zive Sp2)
ZIVE SP2 Instruction manual 5. Front board (Single channel; ZIVE SP2) Standard LCD connector Booster board Optional LCD Main board connector connector connector Interface board connector FAN power connector 6. Inter-connecting boards (Single channel; ZIVE SP2) Bottom side Top side... -
Page 37: Appendix 3. Cables & Dummy Cell
ZIVE SP2 Instruction manual Appendix 3. Cables & Dummy cell 1. Cell cable - 37 -... -
Page 38: Aux Cable
ZIVE SP2 Instruction manual 2. Aux cable - 38 -... -
Page 39: Zra Cable
ZIVE SP2 Instruction manual 3. ZRA cable - 39 -... -
Page 40: Misc Cable
ZIVE SP2 Instruction manual 4. Misc cable - 40 -... -
Page 41: Booster Interface Cable
ZIVE SP2 Instruction manual 5. Booster Interface cable - 41 -... -
Page 42: Dummy Cell
ZIVE SP2 Instruction manual 6. Dummy Cell - 42 -... -
Page 43: Appendix 4. Front Panel Connectors
ZIVE SP2 Instruction manual Appendix 4. Front Panel Connectors 1. Aux connector 2. Misc connector - 43 -... -
Page 44: Cell Connector
ZIVE SP2 Instruction manual 3. Cell Connector - 44 -... -
Page 45: Appendix 5 : Ce Certificate
ZIVE SP2 Instruction manual Appendix 5 : CE certificate 1. Declaration of conformity - 45 -... -
Page 46: Emc Test Report
ZIVE SP2 Instruction manual 2. EMC test report - 46 -...