Advertisement
2. cOntentS and SpecIFIcatIOnS
2.1
carton content
2.1.1
Carefully unpack the carton.
2.1.2
locate the two side clasps (fig.1.6) which hold the top section
(fig.1.3) in place.
2.1.3
undo the clasps, remove the top section and take out the items
in the container.
2.1.4
Check and identify each component as listed below. If anything
is missing or damaged please contact your supplier immediately.
Item
. . . . . . . . . . . . .
.description
1 . . . . . . . . . . . . . . . . . . . . Handle.
2 . . . . . . . . . . . . . .oN/off switch.
3 . . . . . . . . . . . . . . . . . top section.
4 . . . . . . . . . . . . . . . . filter basket.
5 . . . . . . . . . . . . safety float valve.
6 . . . . . . . . . . . . . . . . . . . . . Clasp.
7 . . . . . . . . . . . . . . . . . . Container.
8 . . . . . . Vacuum hose connection.
9 . . . . . . . . . . . . . . . . . . . . Castors.
2.2
Specification
model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PC200
motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250W
supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
maximum Vacuum Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140mbar
Air flow: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120m³/hr
drum size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20ltr
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5kg
Vac Accessories Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35mm
filter type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cartridge
replacement locking Cartridge filter: . . . . . . . . . . . . . . . . . . . PC200Cfl
replacement foam filters (Pack of 10): . . . . . . . . . . . . . . . . PC200ff10
optional dust Bags (Pack of 5): . . . . . . . . . . . . . . . . . . . . . . . . PC200PB5
3. aSSemBly
3.1
ensure the mains plug is disconnected. (fig.2.1)
3.2
undo clasps. (fig.2.2)
3.3
lift off the top section assembly. (fig.2.3)
3.4
remove contents from inside the container. (fig.2.4)
3.5
a) turn the container upside down and insert the castor assemblies and
secure with a screw. (fig.2.5a)
b) Insert the rear wheel assembly and secure with screw. (fig.2.5b)
3.6
for dry vacuum cleaning use the locking cartridge filter supplied. (fig.2.6)
3.7
for wet vacuum cleaning fit the supplied foam filter. (fig.2.7)
nOte: do not operate the cleaner without a filter fitted as this will damage
the vacuum cleaner and invalidate your warranty.
3.8
replace the top section onto the container. (fig.2.8)
3.9
Align up the top section with the clasps and snap into place, by applying
pressure at the mid point of the clasps. (fig.2.9)
3.10
Insert the large end of the hose into the front inlet of the container and
lock in place by turning clockwise a quarter turn. (fig.2.10)
3.11
Choose the desired nozzle and push it onto the telescopic suction tube.
4. dry vacuum cleanInG
WARNING! Ensure you read, understand and apply Section 1 'Safety Instructions'.
Reminder: DO NOT vacuum hazardous substances. Use of an incorrect cartridge filter will invalidate your warranty.
4.1
ensure the machine is unplugged from the power supply. (fig.3.1)
4.2
remove the top section and with the raised rim uppermost fit the cartridge
filter tube down over the filter basket and push fully home. Place the locking
disc onto the top of the filter and turn the locking bar until the latch drops into
the slot in the top of the filter cage. Continue turning until the filter is fully
locked down. (fig.3.2)
4.3
reposition the head onto the drum body, and clip in place. (fig.3.3)
4.4
Insert the larger end of the flexible hose into the front inlet on the
container and lock in place. Push the required attachment onto the free end of
the hose. (fig.3.4)
4.5
Plug in the power supply. (fig.3.5)
4.6
switch to the 'on' (position 'I'). (fig.3.6)
4.7
When you have completed vacuuming, press the switch to 'off'.
5. wet vacuum cleanInG
warnInG! Ensure you read, understand and apply Section 1 'Safety Instructions'. Reminder: remove plug from power supply
before opening unit. dO nOt vacuum solvents, explosives, inflammable and/or hazardous liquids such as petrol, oil, spirits, paint,
thinners, acids etc.
10 . . . . . . . flexible vacuum hose.
11 . . . . three piece vacuum tube.
12 . . . . . . . . . . . . Blow connection.
13 . . . . . . . . large vacuum nozzle.
14 . . . . . . . . . . . . . . . Noise muffler
15 . . . . . . . . . foamed plastic filter.
16 . . . . . . . . . . . . . Crevice nozzle.
17 . . . . . . . locking Cartridge filter
. . . . . . . . . (supplied as standard)
Original Language Version
fig.2
fig.3
fig.1
PC200.V3
Issue No.2
16/10/09
Advertisement
