Advertisement
!3 Video Output Connector [VIDEO OUT]
This connector is for connecting with the
VIDEO IN connector of the video monitor.
Whenever the multiplexed vertical drive (VD2)
signal is supplied to this connector, the cam-
era synchronization mode is automatically set
to Vertical Drive.
CONNECTIONS
A. WV-CL270 (220 V - 240 V AC 50 Hz)
Connect the power cord to an electrical outlet
of 220V - 240V AC 50Hz.
B. WV-CL274E (24 V AC 50 Hz)
Connect the power cable to the AC 24 V IN
terminal on the rear panel of the WV-CL274E.
1
2
24 V AC, 50 Hz
(19.5 V - 28 V)
Recommended wire gauge sizes for 24 V AC line
Copper wire
#24
#22
#20
size (AWG)
(0.22mm
2
)
(0.33mm
2
)
(0.52mm
2
)
(0.83mm
(m)
95
150
255
Length
of cable
(Approx.)
(ft)
314
495
842
Video Cable
1. It is recommended to use a monitor whose
resolution is at least equal to that of the
camera.
2. The maximum extensible coaxial cable
length between the camera and the moni-
tor is shown below.
Type of
RG-59/U
RG-6U RG-11/U RG-15/U
coaxial cable
(3C-2V)
(5C-2V) (7C-2V)
(10C-2V)
Recommended (m)
250
500
600
maximum
cable length
(ft)
825
1 650
1 980
Caution: Connect to 24 V AC (19.5 V-28 V)
class 2 power supply only. Make sure to
connect the grounding lead to the GND
terminal when the power is supplied from a
24 V AC power source.
Installation of Auto Iris Lens
Connector
Install the lens connector when using a video
drive ALC lens.
Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover of the sup-
plied connector as shown in the diagram.
The pin assignment of the lens connector is as fol-
lows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 0.7 V[p-p]/40 kΩ
Pin 4: Shield, ground
Rib
Pin 3
Pin 1
Pin 4
Pin 2
#18
2
)
Solder the lens cable to the pins of the sup-
425
plied connector.
1 403
Mounting the Lens
q Before you mount the lens, loosen the screw
on the side of the camera, and rotate the
flange-back adjusting ring clockwise until it
stops. If the ring is not at the end, the inner
lens or CCD image sensor may be damaged.
w Mount the lens by turning it clockwise on the
lens mount of the camera.
e Connect the lens cable to the auto iris lens
connector on the side of the camera.
800
q
2 640
Focus fixing screw
e
Caution for Mounting the Lens
The lens mount should be a CS-mount (1"-32UN)
and the lens weight should be less than 450 g
(0.99 lbs). If the lens is heavier, both the lens and
camera should be secured by using the support-
er.
The protrusion at the rear of the lens should be as
shown below.
CS-mount: Less than 4 mm (5/32")
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by
qualified service personnel or system installers.
q Loosen the screw on the side of the camera.
SPECIFICATIONS
Pick-up device:
Scanning area:
Synchronization:
Scanning system:
Scanning:
Horizontal:
Vertical:
Horizontal resolution:
Video output:
Signal-to-noise ratio:
Electronic light control:
Minimum illumination:
Detail:
Lens mount:
Ambient operating temperature:
Ambient operating humidity:
Power source and
power consumption:
Dimensions (without lens):
Weights (without lens):
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
w
STANDARD ACCESSORIES
Body cap ...........................................................................................1 pc.
ALC lens connector ...........................................................................1 pc.
OPTIONAL ACCESSORIES
Lenses: WV-LA6AE, WV-LA12AE, WV-LZ81/6E, WV-LZ81/10E, WV-LA4R5AE, WV-LZ80/2E
2003
© Matsushita Electric Industrial Co., Ltd. All rights reserved
w Turn the flange-back adjusting ring to the
desired position.
e Tighten the screw on the side of the camera.
Note: Tightening the screw by force will
Focus fixing screw
Flange-back
adjusting ring
752 (H) x 582 (V) pixels, interline transfer CCD
6.45 (H) x 4.84 (V) mm (equivalent to scanning area of 1/2"
pick-up tube)
internal, line-locked or multiplexed vertical drive (VD2),
selectable
2 : 1 interlace
625 lines / 50 fields / 25 frames
15.625 kHz
50 Hz
480 lines
1.0 V[p-p] PAL composite 75 Ω / BNC connector
50 dB (equivalent to AGC Off, weight On)
equivalent to continuous variable shutter speed between 1/50 s
and 1/15 000 s
0.8 lx (0.08 foot-candle) at F1.4
SHARP or SOFT, selectable
CS-mount
−10 °C - +50 °C (14 °F - 122 °F)
less than 90 %
WV-CL270:
220 V - 240 V AC 50 Hz, 3.8 W
WV-CL274E:
24 V AC 50 Hz, 3.5 W
67 mm (W) x 65 mm (H) x 123 mm (D)
2-5/8" (W) x 2-9/16" (H) x 4-13/16" (D)
WV-
CL270
:
0.495 kg (1.09 lbs)
WV-
:
0.35 kg (0.77 lbs)
CL274E
Matsushita Electric Industrial Co., Ltd.
Osaka, Japan
http://www.panasonic.co.jp/global/
cause damage to the screw or deviation
of focus.
Advertisement
