Table of Contents
Advertisement
Quick Links
6/26/13
Manual of 3 Axis Brushless Gimbal Handheld & Multicopter use.
Thanks for purchasing our 3 Axis Brushless Gimbal. Please read this manual carefully. In that we have no control over the correct use, installation,
application, or maintenance of our products, no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of the
product. Any claims arising from the operating, failure or malfunctioning etc. will be denied. We assume no liability for personal injury,
property damage or consequential damages resulting from our product or our workmanship. As far as is legally permitted, the obligation to
compensation is limited to the invoice amount of the affected product.
Features:
CINESTAR, Droidworks, Hoverfly, Microcopter 3 Axis Brushless
GIMBAL system & Steadicam
This Gimbal will fit Cinestar, droidworks, hoverfly with no modification & work with any large multi rotor that will lift 25lb an more.
1. 3 x 5208 motor that will lift up to 10lb
2. Bearings on all 3 Axes Pitch, Yaw & Roll
3. Gimbal 60 degree on Roll axis left right (can be modified)
4. Gimbal 360 degree on Pitch axis left up down
5. Gimbal 360 degree on Yaw axis around
6. Landing gear with motor cage in the Center hub including barins fit 5208/5206 motor
7. Compatible with all 2 Axis, 3 Axis Brushless controllers
Specification:
wayes under 1000kg, 4mm 3k Carbon fiber Matt, 25mm 3k Carbon Fiber tube Matt, height , width, length, color black
motors Specification:
Model NO.: GBM5208-150
Weight:168g
Motor Dimensions:63x25mm
Stator Dimensions:52x8mm
Copper wire(OD):0.27mm
Configuration:12N14P
Resistance:10.2 ohms
Wind type and termination method:Star style
Pre-wounded with 150 turns,5.0mm shaft
Flexible Mounting Holes:
Bottom mounting holes: (3 holes) 32mm center to center,(4 holes)25mm center to center
Top mounting holes: (2 holes)12mm center to center,(3 holes)17mm center to center
force applied : 600-1500g
Begin To Use Your New Brushless Gimbal:
1. Assembly
Put parts together do not tighten the clamp bolts are facing upwards press nuts downwards except for center cage of the landing gear.
file:///C:/Documents and Settings/og/My Documents/My Pictures/gimbal/setup/setup.html
setup.html
1/4
Advertisement
Table of Contents
Summary of Contents for iPower GBM5208-150
- Page 1 7. Compatible with all 2 Axis, 3 Axis Brushless controllers Specification: wayes under 1000kg, 4mm 3k Carbon fiber Matt, 25mm 3k Carbon Fiber tube Matt, height , width, length, color black motors Specification: Model NO.: GBM5208-150 Weight:168g Motor Dimensions:63x25mm Stator Dimensions:52x8mm Copper wire(OD):0.27mm...
- Page 2 6/26/13 setup.html 2. Fitting should be loose You will tighten after adjusting the parts to level "using a level" in X and Y axis. After you find the level point hold it and tighten the 25mm clamps till joint no longer moves. All Joints must be level on there own plane. Set up for use: 1.
- Page 3 6/26/13 setup.html 2. Balancing the camera Roll Move the camera forward or backward in its tray until it is balanced with the tilt Axis at 90 degrees or as much as possible. when you're happy tighten the clamps on Tilt Axis assembly & camera tray. 3.
- Page 4 6/26/13 setup.html Software Additional resources: http://v.youku.com/v_show/id_XNTIxODI0MDg0.html Martenez: -1?The source code: http://code .google .com /p/brushle ss-gim bal/downloads/de tail?nam e =_043_A.rar&can=2&q= -2?Debug software and firmware download: http://code .google .com /p/brushle ss-gim bal/downloads/list -3?USB computer driver download: http://www.ftdichip.com /Drive rs/VC P.htm -4?The m otor inform ation: http://www.sim ple bgc.com /e le ctronics/m otor_re wind/ -5?De taile d inform ation, ple ase unde rstand the we bsite : http://code .google .com /p/brushle ss-gim bal/...
Need help?
Do you have a question about the GBM5208-150 and is the answer not in the manual?
Questions and answers