Advertisement
Created 23/12/14
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
Features tilt and swivel head for optimum air circulation. Remote control operation and fully guarded fan blades for ease-of-use and extra safety.
Smooth running motor powers both fan blades and head oscillation. Timer function allows user to preset running time between 30 minutes - 7.5
hours. Features three modes - Normal, Nature and Sleep. Nature mode for alternating high and low airfl ows. Sleep mode for gradual reduction
of fan speed. Supplied with wall bracket for quick and easy installation.
3. SPECIFICATION
Fan Diameter: ............................................................................................400mm (16")
Speeds: ....................................................................................................................... 3
Modes: ........................................................................................ Normal, Nature, Sleep
Maximum Airfl ow: .......................................................................................... 53mtr³/min
Power:.....................................................................................................................50W
Supply: ...................................................................................................................230V
Weight: ................................................................................................................ 2.37kg
Height ................................................................................................................ 500mm
4. ASSEMBLY
4.1. Assemble the fan as follows:
Unscrew and remove the large plastic locking cap from the motor spindle of the fan (Note:
left hand thread). Then unscrew and remove the plastic locking ring (Fig.1.1) from the motor
housing.
4.2. Fitting the rear fan guard: Identify the rear fan guard by the location holes in the centre plate
(Fig.1.2) and place the guard over the fan spindle and fi t onto the three location pins (Fig.1.3).
4.3. Secure the rear guard with the plastic locking ring (Fig.1.1).
4.4. Fitting the fan blade. Slide the fan blade onto the motor spindle until it comes to rest against
the pin, ensure the pin engages with the cutouts on the blade. Thread the large plastic locking
cap onto the end of the motor spindle by turning it anticlockwise. Hold one of the fan blades and
tighten the cap down onto the fan.
4.5. Fitting the front fan guard to the rear fan guard. Hook the clip on the top of the front guard
(Fig.2.A) over the rear guard and fi t and tighten the screw and nut at the bottom of the guards
(Fig.2.B). Slide the four other clips on the front guard down to secure the guards together.
4.6. Check that the guard has been assembled correctly and that the fan will turn freely before
plugging into the mains. The fan is now ready to use.
5. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions
in Section 1 before using the fan.
5.1. Mount on a suitable wall location using the bracket and three fi xings. Secure the fan to the
bracket using the thumbscrew. Plug into the mains power supply.
5.2. Adjust tilt of fan as required.
5.3. On the Fan Bracket. To start the fan, press the ON/SPEED button. To adjust the Speed press
the ON/SPEED button to sequence through LOW MED HI. To stop the fan, Press the OFF
button. To start/stop oscillation, press the OSCIL button.
5.4. On the Remote. To start the fan, press the ON/SPEED button. To adjust the Speed press the
ON/SPEED button to sequence through LOW MED HI. To stop the fan, Press the OFF button.
To start/stop oscillation, press the SWING button.
5.5. To set the MODE. On the Remote, press the MODE button. Modes are NOR - constant speed.
NAT - fast / slow alternating speed. SLP - fast / slow alternating speed, set stop time by using TIMER.
5.6. To set the TIMER. On the Remote, press the TIMER button. The timer can be set from 30 minutes to 7 hours and 30 minutes. Press the
TIMER button to sequence through 30 minute timer intervals to select desired timer duration.
5.7. When the fan is no longer required, press the OFF button and remove plug from mains socket.
Store in a safe, dry, childproof location.
6. CARE OF FAN
IMPORTANT: Turn the fan OFF and disconnect from power supply before cleaning.
6.1. Use only a soft, damp cloth to clean the fan.
6.2. DO NOT submerse the fan in water and NEVER allow water to drip into the motor housing.
6.3. DO NOT use solvents or other chemicals to clean the fan.
6.4. To clean the fan blades, remove front guard - reverse of assembly sequence 4.5. above.
6.5. Wipe the blades and guards clean.
6.6. Reassemble front guard - see assembly sequence 4.5. and 4.6. above.
6.7. Store the fan in its original box or otherwise cover the fan to protect it from dust.
Page 2
Original Language Version
Fig. 1
Fig. 2
SWF16WR.V3 | Issue 1
Advertisement
