Subscribe to Our Youtube Channel
Summary of Contents for GRAUPNER TS100
- Page 1 Manual Portable Smart Soldering Station TS100 12/24V computer-controlled, programmable, adjustable temperature No. 94412...
- Page 2 2 / 2 S8474_PDB_SBEC_V_1_jh...
-
Page 3: Table Of Contents
Index Introduction ................4 Service Centre ...............4 Intended use .................5 Technical Data ...............5 Declaration of conformity ............5 Symbols explication ...............6 Safety notes ................6 Connection and operation .............7 Default settings ..............7 Basic control .................7 Heating up ................8 System parameter ..............9 Changing the tip ..............9 Optional soldering tip (not included) ........10 Soldering iron tip maintenance ..........10 Changing default settings ............10... -
Page 4: Introduction
Read this manual carefully to achieve the best results with your Soldering Station. If you experience any trouble during operation, take the instructions to help or ask your dealer or Graupner Ser- vice Centre. Due to technical changes, the information may be changed in this manual without prior notice. -
Page 5: Intended Use
Target group The product is not a toy. It is not suitable for children under 14 years. The operation of the TS100 Soldering Station must be per- formed by experienced users. Package content TS100 Soldering Station ... -
Page 6: Symbols Explication
Use the ST100 Soldering Station only within the indicated volt- age range, risk of fire! The TS100 Soldering Station is conceived to be powered by Lithium batteries or by a suitable power supply. Use the TS100 Soldering Station only with power sources whose volt- age and current match with the technical data table. -
Page 7: Connection And Operation
Connection and operation 1. Loosen the tip setscrew, insert the soldering tip and tighten the screw; 2. Connect the ground wire to the setscrew; 3. Connect the power supply to the soldering station and switch it on. Note If the screen displays „sen-err when it’s plugged, it means that the soldering tip is not properly fixed. -
Page 8: Heating Up
Heating up When pressing the button A in standby mode, the Soldering Sta- Pres s 30 0℃ tion will heat up to the preset tem- perature. When OLED displays as picture, it means that the Soldering Sta- 3 00℃ tion is ready for soldering. In operation mode, holding both buttons for 3 seconds will return to standby mode. -
Page 9: System Parameter
If you do not use the Soldering Station for more than 3 minutes (standard setting) while it is in use mode, then the sleep mode 2 00℃ will be active. Temperature is automatically set to the preset sleep temperature. As soon as the Soldering Station is used again, it will change automatically to the use mode. -
Page 10: Optional Soldering Tip (Not Included)
Open the config.txt file from the USB drive, set the default parameters. Firmware update Visit www.graupner.de and download the latest Soldering Station firmware to your PC. Connect the Soldering Station to your PC with the USB data cable, meanwhile, press the button A on the Soldering Station to enter the DFU mode. -
Page 11: Trouble Shooting
Trouble shooting Problem Recommended possible solution No display Check: Is the cable broken? Check: Is there any data in USB mode? Every time when installing The device checks the status, it is normal a new tip, the tempera- ture status displays random numbers The Soldering Station Check 1: Is the power source properly plugged? -
Page 12: Notes On Environmental Protection
The present construction or user manual is for informational pur- poses only and may be changed without prior notice. The cur- rent version can be found on the Internet at www.graupner.de on the relevant product page. In addition, the company Graupner has no responsibility or liability for any errors or inaccuracies that may appear in construction or operation manuals.
Need help?
Do you have a question about the TS100 and is the answer not in the manual?
Questions and answers