Duplomatic EDM-M*/30 Series Startup Manual

Duplomatic EDM-M*/30 Series Startup Manual

Digital card

Advertisement

EDM-M*/30
Digital Card
Start - up
manual
Duplomatic MS Spa
89251/218 ETM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EDM-M*/30 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Duplomatic EDM-M*/30 Series

  • Page 1 EDM-M*/30 Digital Card Start - up manual Duplomatic MS Spa 89251/218 ETM...
  • Page 2: Table Of Contents

    Parameters ............................26 APPENDIX 2: Block diagrams ........................28 EDM-M1 ............................28 EDM-M2 ............................28 EDM-M3 ............................29 Function of pin 12..........................29 page 2 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 3: General Info

    EDM-M3****/30E*-B by Duplomatic MS S.p.A. Should you have any questions concerning just the card, please contact Duplomatic MS S.p.A., indicating the description, the code and the serial number written in the label on case side. Other useful literature about EDM-M/30 and its start-up can be found in:...
  • Page 4: Features

    Separate PWM settings (PWM-Dither) in the 2-channels version EDM-M3 Enable signal (version A only) Parameters programmable via software: Ramps, deadband compensation, scaling of analogue inputs Fault recognition (cable breaks, short-circuits, etc.) page 4 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 5: Available Versions

    A = Pin 12 used for external enable (Non-existing configuration in previous series 20) B = Pin 12 used for V aux (internal enable) - Series 20 compatible. page 5 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 6: Diagnostic

    B with a negative value of voltage or a current between 4…12 mA. M3 version (for two valves with one coil each), requires that both the analogue inputs must be used. page 6 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 7: Led Description

    Missing power voltage (just USB connected) NOTE: LEDS blinking all together even when the USB communication is active but the card is not powered. page 7 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 8: Technical Characteristics

    Housing material Connections Plug-in terminal block with tightening screws: 15 poles micro USB-B Operating temperature range °C -20 / +70 Protection degree IP 20 page 8 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 9: Overall And Mounting Dimensions

    Overall and mounting dimensions page 9 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 10: Installation Instructions

    It is recommended using a regulated power supply (linear or switching mode) for card supply and for the sensors. page 10 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 11: Pin Tables

    Auxiliary voltage output for potentiometer +10 V PIN 14 Auxiliary voltage output for potentiometer -10 V PIN 15 0V reference PIN 13 and PIN 14 page 11 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 12: Edm-M2

    Auxiliary voltage output for potentiometer +10 V PIN 14 Auxiliary voltage output for potentiometer -10 V PIN 15 0 V reference for PIN 13 and PIN 14 page 12 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 13: Edm-M3

    Auxiliary voltage output for potentiometer +10 V PIN 14 Auxiliary voltage output for potentiometer -10 V PIN 15 0 V reference for PIN 9, PIN 13 and PIN 14 page 13 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 14: Wiring

    Wiring page 14 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 15: Card Setup

    On-line registration is required at first access. Once registered the app can even work off-line. The EBC app allows diagnostic and configuration activities of USER level parameters. Password is required to apply parameters changes. See Parameters section. page 15 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 16: Ebc Configurator Software

    USB port. Leds blink all together for signalling the USB communication. If you need to energize the valve simultaneously, you need the power supply to pins 1/2. page 16 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 17: Parameters

    0…10V | 4…20mA M1-M2 code (M1 version) versions +/-10V | 4…12…20mA (M2 version) SIGNAL1_TYPE According with ordered 0…10V | 4…20mA M3 version code SIGNAL2_TYPE page 17 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 18 M2 version ADJ_MAX_A 100% ADJ_MIN_A – 120% ADJ_TRIGGER 1.5% 0 – 20% ADJ_MIN_B According with version ADJ_MIN_B – 120% ADJ_MAX_B 100% 0 – 50% page 18 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 19: Configuration

    AUTO: Auto reset mode. All monitoring functions are active. If the failure does not exist anymore, the module automatically resumes to work. DISABLE: No monitoring function is active. page 19 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 20: Enable (To Activate External Enable Of Power Stage)

    ▪ Signal input must be scaled from 2.5V to Standard Full Scale of 10V - > SIGNAL_GAIN = Standard F.S. / Application F.S. = 10 / 2.5 = 4.0 page 20 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 21: Ramps

    RAMP2_UP RAMP2_DOWN Entered ramp time is related to 100% of signal variation. Different ramps times are available for each quadrant in EDM-M2 card: page 21 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 22: Output Signals

    This value returns the nominal resistance of the coil. It is exploited to optimize the control algorithm. RESIST is a read-only parameter, valorised in factory and is dependent on the ordered card version. page 22 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 23: Curve Adjustment

    (dead band of the valve) will be compensated with the ‘MIN’ value. Via the TRIGGER the activation point of the MIN function is set and so a non-sensitive range around the zero- point can be specified. page 23 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 24: Pwm

    The dither amplitude is defined in % of the nominal current (see: CURRENT command). The upper limit for Dither frequency is half of PWM frequency selected. page 24 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 25: Process Data (Monitoring)

    TEMP_BOARD Temperature of the board °C TEMP_PWRSTG Temperature of the power stage of the board °C V_CTRL Supply voltage V_PWRSTG Power stage voltage page 25 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 26: Appendix 1: Edm-M/20 Migration

    RAMP_DOWN RAMP_UP_A, RAMP_DOWN_A, RAMP_UP_B, 0…20000 Ramp Up, 0…99 [%] RAMP_DOWN_B [ms] Ramp Dn (PI1) Ramp Up, RAMP1_UP, Ramp Dn (PI2) RAMP1_DOWN, RAMP2_UP, RAMP2_DOWN page 26 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 27 CURRENTx DITHER2_AMP [%] 10…PWM/2 M1 or DITHER_FREQ [%] Dither Freq PWM ≤ 198 0…PWM/2 [Hz] DITHER1_FREQ, 10…99 if DITHER2_FREQ [%] PWM > 198 page 27 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 28: Appendix 2: Block Diagrams

    APPENDIX 2: Block diagrams EDM-M1 EDM-M2 page 28 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...
  • Page 29: Edm-M3

    EDM-M3 Function of pin 12 page 29 of 29 Duplomatic MS S.p.A. ▪ EDM-M*/30 Start-up Manual ▪ 89251/218 ETM ▪ Jun 2018...

Table of Contents

Save PDF