Advertisement
Quick Links
Installation guide
Sensor module for DIN rail mounting
The LCN-SHS is a sensor module for building installation in Bus technology. It has the
same functions as the LCN-SH, however without electronic (dimming) outputs.
power side
LCN
LCN-SHS
Sensor-Modul
Controller
U =230V, P =0.4W
N
status LEDs
push button-
connection
sensor side
Local Control Network - building controls in perfection
phase
N
data
V
impulse sensor-
connection
periphery
connection
Application
The 2HP sized LCN-SHS module is for installing in
dry rooms in main and normal distribution boxes.
It has 3 electronic outputs (see illustration), which
are seperately controlled. Amongst other things,
the push-button converters LCN-BT4H / LCN-
BU4L, the relay contacts LCN-R8H / LCN-R2H /
LCN-R4M2H and also the binary sensors LCN-
BT4H/LCN-BU4L (as mentioned above) can be
connected.
The operating programme from the LCN-SHS
includes further functions like 2 proportional
regulators, 5 thresholds, the LCN panel system
etc..
LCN-SHS
®
1
Advertisement
Summary of Contents for Local Control Network LCN-SHS Series
- Page 1 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Sensor module for DIN rail mounting The LCN-SHS is a sensor module for building installation in Bus technology. It has the same functions as the LCN-SH, however without electronic (dimming) outputs.
- Page 2 LCN-SHS ® Installation guide Local Control Network - building controls in perfection The connection The module has two connecting blocks: the power supply side with screwless terminals and the sensor side with three plug connections. The terminals are colourfully marked as follows...
- Page 3 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Sensor technology The red sensor connecting plugs are protected only in a low extent against overvoltage. A contact with 230V will destroy the module. The sensor terminals are on the N potential, which means they are not decoupled from the electrical isolation.
- Page 4 LCN-SHS ® Installation guide Local Control Network - building controls in perfection P-connection: Here you can connect for example, the 4-way binary sensor (LCN-BT4H/-BU4L), the current sensor (LCN-BS4) and the relay blocks (LCN-R8H/-R4M2H/-R2H. The LCN- BT4H/BU4L and LCN-BS4 will be detected automatically. The LCN-R8H has to be activated first with the LCN-P or LCN-PRO .
- Page 5 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Status display of the lamps GREEN (flashes constantly): nr. of flashes message normal operation self testing-error, module is not programmed bus error: module cannot send (reserved) module is in programming mode RED (flashes only when occurances are entered): nr.
- Page 6 LCN-SHS ® Installation guide Local Control Network - building controls in perfection In the menus and help texts found in the programme LCN-PRO, further informations and properties of the module are available. Without parameterization the module has no functions. Because no access to the module is required when first programming, (no programming button, all functions are controlled over the bus), the module may be installed before being setting up.
- Page 7 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Properties of the built-in control progamme:: Issued numbers: module ID: 5..254, group nr.: 5..254 segment nr.: 5..124 group members: 12 (fixed) plus 10 (dynamic) command tables: A, B, C & D with each 2 * 8 targets...
- Page 8 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Properties of the built-in control progamme: Measured value processing triggering: 8, 10 or 12 bit pre processing: value correction, hum sound suppression, remote query two continuous controllers evaluation:...
- Page 9 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Technical data: Connection: power supply: 230VAC 15%, 50/60Hz (110VAC version available) ± power consumption: 0,4W screwless, solid max. 2,5mm² oder fine wire with end sleeves terminals/wire type (load side): max.
- Page 10 LCN-SHS ® Installation guide Local Control Network - building controls in perfection Technical data: Installation: operating temperature: -10 C..+ 40 C air humitidy: max. 80% rel., non condensing use as stationary installation according to VDE632, VDE637 environmental conditions: protection art:...