1. Manuals
  2. Brands
  3. Auric Pro Manuals
  4. Computer Hardware
  5. Octo
  6. Owner's manual

Auric Pro Octo Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Octo
Manual
DIGITAL PROCESSOR
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Octo and is the answer not in the manual?

Questions and answers

Summary of Contents for Auric Pro Octo

  • Page 1 Octo Manual DIGITAL PROCESSOR Owner's Manual...
  • Page 2 WARNING This device is equipped with high voltage elements. Do not open the shell if not necessary. Pay attention to the risk of electric shock when checking or modifying the device. The responsibility of decline of quality or burn down of the device caused by owner's modifying or disoperation is not included in the warranty.

  • Page 3: Table Of Contents

    Octo Introduction Table of Contents Section 1-Introduction 1.1 Brief Introduction Section 1 - Introduction Congratulations on your purchase of the K-5200. The K-5200 is the newest digital processor ..................... 1 which developed independently, quipped with a touchable screen, 32 bit DSP, 4 ways MIC inp 1.1 Brief Introduction ......................

  • Page 4: Section 2 - Quick Started

    Octo Octo Quick start Quick start 2.2 Front Panel Section 2-Quick start 2.1 Connection Diagram Professi onal Di gi tal Audi o Process or K-5200 MENU Mic 1 16:06 1. Please follow the proceeding steps to set up and running quickly. Please ensure the power to...

  • Page 5: Rear Panel

    Octo Octo Quick start Quick start 2.3 Rear Panel 2.4 Display & Control 1. The touch screen on K-5200 allows users to access different menus and edit various paramete rs. There are 6 menus can be accessed on main interface as below, including MIC, MUSIC, EFFE CT, OUTPUT, SYSTEM, MODE.

  • Page 6: Section 3- Processing & Parameters

    K-5200 K-5200 Quick start Processing & Parameters 3. On main interface, Pressing the ESC button or rotating any of the combinational function knobs Section 3- Processing & Parameters will get into the VOLUME page as below, which including the volume adjustment of MIC1~4, EFF ECT, MUSIC, OUTPUT and all MIC.
  • Page 7 K-5200 K-5200 Processing & Parameters Processing & Parameters PAGE 1/5 PAGE 4/5 MIC1~4 FILTER MIC FEED BACK HIGH PASS 6 degrees feedback inhibition, range:-3~+3; OFF; -3~-1 are negative inhibition, +1~+3 are Range: 20Hz~20000Hz Preset 8 types of High-pass filtering: BL_12, BW_12, LK_12, UR_12, BL_24, BW_24, active inhibition, each degree contains 0.2Hz.

  • Page 8: Music Setting

    Octo Octo Processing & Parameters Processing & Parameters 3.2 MUSIC Setting PAGE 3/5 COMPRESS SETTINGS COMP SWITCH MUSIC ON/OFF, it is used to compress the dynamic range and tighten uneven parts of audio signals. COMP THRSH Range:-25~+25, it is used to set the signal level at which the compressor starts to work. If the MUSIC PAGE2/5 threshold level is set at -10dB, only signals that pass above -10dB will be compressed;...

  • Page 9: Effect Setting

    Octo Octo Processing & Parameters Processing & Parameters FREQ Range: 20Hz~20000Hz; REVERB is the ambient sound of various live environments such as clubs, studios, TYPE: PEQ: Manipulates a set range of frequencies, out in both directions from the center freq concert halls, etc.
  • Page 10 Octo Octo Processing & Parameters Processing & Parameters PAGE 6/8 ECHO SETTINGS LOW PASS It adjusts the frequency of the reverb low pass filter. Lower values will allow the lower frequ ECHO PRE DELAY encies to pass through the reverb effect creating a fuller, darker reverb, whereas higher values...

  • Page 11: Output Setting

    Octo Octo Processing & Parameters Processing & Parameters PAGE 8/8 PAGE 1/5 ECHO-EQ OUT 1~8 MUTE ON/OFF, it is used to turn on or off the EQ editor. ON/OFF, it is the switch to turn on or off the output signal of OUT 1~8;...

  • Page 12: System Setting

    Octo Octo Processing & Parameters Processing & Parameters 3.5 SYSTEM Setting -10dB would remain untouched. Generally, for speaker protection, you would want to use limiting, where most of the signal content remains just below the threshold and only the peaks cross the threshold and get limited;...

  • Page 13: Mode Setting

    K-5200 K-5200 Processing & Parameters Processing & Parameters Select the corresponding Baudrate for connecting by the RS232 port. 3.6 MODE Setting NOISE GATE SWITCH ON/OFF, it is the switch to turn on or off the Noise Gate. MODE NOISE GATE GAIN Range: -80dB~-50dB, 3dB for each degree, when the Noise Gate is turn on, the signal higher than the setting level will pass, and the one lower than it will be decayed.

  • Page 14: Remote Control

    OCTO OCTO Appendix Appendix 4.4 Technical Specifications 4.2 Remote Control Microphone Inputs: SNR: 113dB Users can use the remote control which is packed with K-5200 to set the device. THD: ≤0.005%（20Hz~20KHz) Frequency Response: 20Hz~20KHz（±5dB） K-5200 Professi onal Di gi tal Audi o Process or MENU Max Input Level: -11.2dbu...

Table of Contents