Storage & Management after use ----------------------------------- 16 Installation Guide ----------------------------------------------------- 17 Components of Box -------------------------------------------------- 26 Mentioned Items ----------------------------------------------------- 27 Map ------------------------------------------------------------------- 28 Introduction Thanks you for purchasing this model (RT-400). Please use RT-400 after read & understand the manual carefully and understand it well.
Service Environment Don’t use it under being exposed to direct sunlight. Recommend to be used under Temperature (Celsius: -10˚C~40˚C / Fahrenheit: 14℉~104℉), Humidity (30% ~ 85%), Air Pressure (70~106Kpa). Install the equipment horizontally and maintain the level for smooth performance.
Symbols & Meanings Means a warning. Displays text or picture near the sign specific information. This means a ban. Displays text or picture near the sign specific information. Means the command. Displays text or picture near the sign specific information. Safety Precaution Symbol Prevent Entry...
Symbol Prevent Entry When you put the device in the table, more than 5˚ Do not place unstable or tilted. May result in injury due to the unit. Do not place heavy objects on the table than the specified value. May result in injury due to the unit. Do not insert your fingers between moving equipment operating unit.
earthquake, acts by third parties, other accidents, user's negligence, misuse or other damage under abnormal operating conditions. Caused by the use of other than those specified in the instruction manual. Manufacturer shall not be liable for any damages at all. Alert and Display Position Warning notices are to ensure safety on the unit.
Page 7
machine is stopped. ⑤ When replacing the fuse, replace turn off the power switch, unplug the power cord from the wall outlet. There is a risk of electric shock.
Page 9
Name of each part & Function ① Table : You can install 3 test equipment. ② Cable Hole : You can send down the equipment power cables. ③ Control box: There is main power, table up/down switch. ④ Lift Column: Assemble Column, Base and Castor. ⑤...
Way of Use Precaution before use ① Check it out Power Voltage (220 ~ 230V) ② Power on the switch. ③ Check it out whether the equipment is working or not After connection the power supply. How to use and operation sequence. Insert the power cord into the power input box ①...
Page 12
On the front of the product into the green control switch to ② the "I" in position, slide and then the green light is turned on (power ON) The table is rising up while pushing up (▲) switch ③ the tables are falling down while pushing down (▼) switch. Slide the "O"...
When Problem Occurs How to operate when a problem occur. Do not disassemble the unit for repair. You may receive an electric shock. Warning Please contact your dealer if necessary for repair. Do not open the control box carelessly You may receive an electric shock Cautions Please contact your dealer if necessary for repair.
Unplug the power cable and make sure that verifying power switch’s place is the "O" position. Open the fuse folder using screwdriver or pointed tool, the folder with the lower end of the input socket. Replace new fuse( 5A 2EA ). Make sure that power switch is off.
Precautions of Use. Do not use in temperatures lower than minus 10 ° (Celsius: -10˚C / Fahrenheit: 14℉) Make sure there are no problems with the unit and overall patient. Take appropriate action, such as when the patient is found in the apparatus and over the patient, to a safe state, and stops the operation of the equipment.
Storage and Management after use. Disconnect the power code after returning to the previous state, and use power table position. Do not force such as holding the cord when you disconnect cords subtracting. Be careful of followings for the storage area. Keep out of reach in the water ...
Installation Guide ※ All our products are tightening bolts. ※ Need the following tools. - Drivers (+) - Hex Wrench. - Spanner(10mm) 1. Check out all parts from the part box. ① Lift Column Base(2 units) ② Reinforce Band(Brackets are fastened) ③...
Page 19
① Remove the table from the control box (Use a Phillips screwdriver) ② Assemble the control box after switch was fastened the bracket.
Page 20
4. Assemble column base into the table. ① Place lift column on the bracket of table bottom.
Page 21
② Tighten list column bracket(Use wrench driver) (Tighten the bolt with a wrench in order - spring washer – flat washer – wrench bolt from below) ※ Bolt & Washer were fastened to the bottom of table.
Page 22
5. Connect the controller to the connector of the lift column. The input terminal of the three controllers must M1, M2 the two input marked by the arrow of the connector cable – for connecting to the terminal after arrange to pass.
Page 24
6. Assemble reinforce band. ① Replace the bracket on the lift column. Use a bolt with cap nut is fastened to the reinforce band bracket. (10mm spanner, hex wrench used) ② Place reinforce band between lift column.
Page 25
③ Tighten bolt and cap nut with reinforce band and reinforce band bracket.
Page 26
7. Please see the previous mounting on the other side. It could be able to do depending on the power input into the indoor environment.