Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RAYLASE IPG
Summary of Contents for RAYLASE IPG
- Page 1 Hardware Manual IPG Interface Board...
- Page 2 This manual has been compiled by RAYLASE for its customers and employees. RAYLASE reserves the right to change the product described in this manual and the infor- mation contained therein without prior notice. The software included in the product and this manual itself are protected by copyright. All rights are reserved.
-
Page 3: Table Of Contents
Dimension and Weight ....................7 Environmental Conditions ....................7 SET-UP Procedure ......................7 Connections........................8 2.4.1 IPG Laser Interface ......................9 2.4.2 Laser Power Input and Laser Power Output ..............10 2.4.3 Cable Specifications ...................... 10 2.4.4 Status LEDs........................10 PROGRAMMING ...................... -
Page 4: Basic Information
Chapter 1 Basic Information BASIC INFORMATION The RAYLASE IPG interface board is used to control a pulsed IPG laser in combination with RAYLASE control cards SP-ICE, RLC-PCI or RLC-USB. Features Interface to Ytterbium pulsed IPG Fiber Lasers according to interface types B, B1, B2, D ... -
Page 5: Signs
The Interface Board conforms to the requirements of the following directives: EU Directive 2004/108/EC (EMC) WEEE Directive 2012/19/EC RoHS II 2011/65/EU For details of conformity with other directives, contact RAYLASE. MN027 / v1.1.0 RAYLASE IPG Interface Board... -
Page 6: Laser Safety
E-mail: info@raylase.de Customer Support The RAYLASE support services are available for your problems either in respect to the prod- uct or the accompanying manual. Before calling for support, please make sure you refer to any appropriate sections in this manual that may answer your questions. -
Page 7: Technical Data
Connect laser power supply output J2 to IPG laser. Connect IPG interface board output J4 to laser interface. Connect RAYLASE control card via adapter to IPG interface board input J3. Switch on laser power supply. After a short delay, the laser will be switched on. -
Page 8: Connections
IPG Interface Input IPG Interface Output page 9 Shutter / Emergency Stop must be connected to switch-on the laser Laser Reset resets the laser or the IPG interface in case of a fault RAYLASE IPG Interface Board MN027 / v1.1.0... -
Page 9: Ipg Laser Interface
Laser modulation MO = Master oscillator [interface type B] nc = Not connected PRR = Pulse Repetion Rate [interface type B] Specifications Output Output low max. 0.55V 64mA 2.0 – 5.0V Output high 32mA MN027 / v1.1.0 RAYLASE IPG Interface Board... -
Page 10: Laser Power Input And Laser Power Output
5V Input Voltage from control card is ready green 24V Input Voltage for laser is ready Soft start process of IPG laser is active. 24V Output green IPG laser is powered up Laser emission ON Laser is active Meaning... -
Page 11: Programming
Programming Chapter 3 PROGRAMMING The following sections describe how to program an IPG laser for use with RAYLASE control card and RAYLASE IPG interface board. Signals Use the following signals to program the IPG interface board: Signals of control card... -
Page 12: Programming Sequence
// Load Correction File Set_Mode (0x0420); // Set YAG1-mode (Bit 5 = 1, Bit 4 = 0) Setting Master Oscillator input of IPG Laser with Control Commands: Set_Start_List_1(); // Filling Job Data into List 1 Set_Delays_7_8 (t1, t2); // Set Laser Modulation Signal Set_Delays_9_10 (t3, t4);... - Page 13 Disposal ............6 Seal label ............5 Environmental Conditions ....... 7 SET-UP Procedure ......... 7 Signs ............... 5 Features ............4 Technical Data ..........7 Installation ............7 Warranty ............4 Weight ............. 7 MN027 / v1.1.0 RAYLASE IPG Interface Board...
Need help?
Do you have a question about the IPG and is the answer not in the manual?
Questions and answers