Table of Contents
Advertisement
Installation and Operating Data
Installation and Operation Manual
HHP, HHPU, MHP & MHPU Jandy
FOR YOUR SAFETY - This product must be installed and serviced by authorized per-
sonnel, qualified in pool/spa installation. Improper installation and/or operation can create
an electrical hazard which can cause serious injury, property damage, or death. Improper
installation and/or operation will void the warranty.
WARNING
ATTENTION INSTALLER:
This manual contains important information about the installation,
operation and safe use of this product. This information should be
given to the owner/operator of this equipment.
®
Pumps
Advertisement
Table of Contents
Summary of Contents for Jandy Pumps HHPU Series
- Page 1 Installation and Operating Data Installation and Operation Manual ® HHP, HHPU, MHP & MHPU Jandy Pumps WARNING FOR YOUR SAFETY - This product must be installed and serviced by authorized per- sonnel, qualified in pool/spa installation. Improper installation and/or operation can create an electrical hazard which can cause serious injury, property damage, or death.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION 7 SECTION 1 Use and Maintenance General Maintenance......8 Safety Information Winterizing the Pump......9 Safety Instructions........4 SECTION 8 SECTION 2 Troubleshooting General Information Troubleshooting........9 Introduction..........5 Description..........5 SECTION 9 Speciality Service SECTION 3 Blocked Impeller........ -
Page 4: Safety Information
Water Pik Technologies, Inc. Page 4 SECTION 1. Safety Information 1A. Safety Instructions READ AND FOLLOW THESE SAFETY INSTRUCTIONS! PLEASE SAVE THESE INSTRUCTIONS Do not start pump dry! Running the pump dry for any length of time will cause severe damage and will void the warranty. -
Page 5: General Information
Page 5 Jandy™ Pumps SECTION 2. Pool owners should use high speed for vacuuming the pool, quick filtering action, priming the General Information heating system, and to keep up with heavy bathing loads. Spa owners will want to use high speed for 2A. -
Page 6: Piping Design And Installation
Water Pik Technologies, Inc. Page 6 Provide access for future service by leaving a The Jandy™ Pump must be connected to at least clear area around the pump. Allow plenty of two separate suction points in the water. A drain space above the pump to remove the lid and and skimmer, two drains spaced apart, two basket for cleaning. -
Page 7: Electrical Verification And Installation
Page 7 Jandy™ Pumps SECTION 5. Caution Electrical Verification & Installation The pump must be permanently connected to a dedicated electrical circuit. No other 5A. Check for Correct Voltage equipment, lights, appliances or outlets may be on the pump circuit. The correct voltage, as specified on the pump nameplate is necessary for proper performance and long motor life. -
Page 8: Start-Up
Water Pik Technologies, Inc. Page 8 SECTION 6. The pump should prime. The time it takes to prime will depend on the elevation and length of Start-up pipe used on the suction supply pipe. See section 4 "Piping Design & Installation" for proper 6A. -
Page 9: Winterizing The Pump
Page 9 Jandy™ Pumps Prior to replacing the lid, check for debris loosened and the pump stored indoors. For around the lid o-ring seat, as this will cause air safety, and to prevent entry of contaminants, leaks into the system. Clean the lid o-ring and reinstall all conduit and terminal box covers. -
Page 10: Speciality Service
Water Pik Technologies, Inc. Page 10 If there are still air leaks check the suction side The pump is leaking water between the motor piping union. and pump body. a. While the pump is running, try to tighten the a. This is caused by a damaged or failed union. -
Page 11: Removing The Pump Housing
Page 11 Jandy™ Pumps 9B. Removing the Pump Body HHP Series Turn off the pump. Switch off the circuit breaker Locatings Locatings Pins (4) to the pump motor. Holes (4) Loosen the suction and discharge unions. This Mounting Diffuser Bracket will allow you to move the pump for easy opening. -
Page 12: Replacing The Pump Housing
Water Pik Technologies, Inc. Page 12 Diffuser O-Ring Diffuser Screws (4) Bolts & Washers (4) Diffuser Mounting Bracket Impeller Mechanical Seal Motor Pump Body O-Ring Mounting Bracket MHP & MHPU Diffuser O-Ring Bolts & Washers (4) Diffuser Screws (3) Diffuser Mounting Bracket Impeller Motor... -
Page 13: Mechanical Seal Replacement
Page 13 Jandy™ Pumps If the pump is located above water level of the Lubricate (water) the perimeter of the new seals pool, remove the lid and fill the basket with rubber gasket. water before starting the pump. Press the ceramic assembly onto the Impeller. Prior to replacing the lid, check for debris around the lid o-ring seat, as this will cause air Use Windex or alcohol to remove any... -
Page 14: Motor Replacement
Exploded Views & Replacement Kit properly disconnect the electrical wiring at the Part Numbers pump motor. To order or purchase parts for Jandy Pumps, contact your Follow steps 1-9 of "Removing the Pump nearest Water Pik Technologies Products dealer or distribu- Body."... -
Page 15: Jandy Tm Hhp Pump Series
Page 15 Jandy™ Pumps Figure 9. HHP Exploded View... - Page 16 Water Pik Technologies, Inc. Page 16 To order or purchase parts for Jandy™ Pumps, contact your nearest Water Pik Technologies Products dealer or distributor. If they cannot supply you with what you need, contact the Customer Service Manager at Water Pik Technologies, Inc. 10B.
-
Page 17: Jandy Tm Mhp & Mhpu Pump Series
Page 17 Jandy™ Pumps Figure 10. MHP & MHPU Exploded View... -
Page 18: Pump Curves
Water Pik Technologies, Inc. Page 18 SECTION 11. Pump Curves 11A. Jandy™ HHP & HHPU Pump Curves 3.0H HP 2.0H HP/2.5HH PU 1.5H HP/2.0HH PU 1.0H HP/1.5HH PU .75H HP/1.0HH PU Feet Jandy H igh Head Pum ps Head Full Rated (HHP) & U p Rated (HHPU) Flow (GP M ) -
Page 19: Jandy™ Mhp & Mhpu Pump Curves
Page 19 Jandy™ Pumps 11B. Jandy™ MHP & MHPU Pump Curves 2.0MHP / 2.5M HPU 1.5MHP / 2.0M HPU 1.0M HP / 1.5M HPU 75M HP / 1.0M HPU .75MHPU Jandy M edium Head Pum ps Feet Full Rated ( M HP) and Up-R ated (M HPU) Head... -
Page 20: Pump Dimensions
Water Pik Technologies, Inc. Page 20 SECTION 12. Pump Dimensions 12A. Jandy™ HHP & HHPU Pump Dimensions MODEL VOLTAGE PIPE CARTON DIMENSIONS SIZE WEIGHT HHP.75 115/230 2" 38lbs. 23 " 13 " HHP1.0 115/230 2" 41lbs. 23½" 13¼" HHP1.5 115/230 2"... -
Page 21: Jandy™ Mhp & Mhpu Pump Dimensions
Page 21 Jandy™ Pumps 12B. Jandy™ MHP & MHPU Pump Dimensions MODEL VOLTAGE PIPE CARTON DIMENSIONS SIZE WEIGHT MHP.75 115/230 2" 38lbs. 23¾" 13¼" MHP1.0 115/230 2" 41lbs. 23¾" 13¼" MHP1.5 115/230 2" 47lbs. 23¾" 13¼" MHP2.0 2" 51lbs. 24¼" 13¾"... - Page 24 LIMITED WARRANTY ® Thank you for purchasing Jandy pool and spa products. Waterpik Technologies (manufacturer of Jandy products, including Laars ® pool and spa heaters) warrants all parts to be free from manufacturing defects in materials and workmanship for a period of one year from the date of retail purchase, with the following exceptions: •...