Download Print this page

Thermal Instrument Co. 62-9FS Installation & Operation Instructions

Flow switches, 220vac, 110vac, 24 vdc, factory set

Advertisement

Quick Links

THERMAL INSTRUMENT Co.
217 Sterner Mill Road, Trevose, PA 19053
Email: office@thermalinstrument.com
INSTALLATION, OPERATION
INSTRUCTIONS
FLOW SWITCHES
62-9FS & 600-9 FS
Telephone No. (215) 355-8400
Fax No. (215) 355-1789
FOR
220VAC
110VAC
24 VDC
Factory Set
Effective Date
7/10/2008
1 |
P a g e

Advertisement

loading
Need help?

Need help?

Do you have a question about the 62-9FS and is the answer not in the manual?

Questions and answers

Summary of Contents for Thermal Instrument Co. 62-9FS

  • Page 1 THERMAL INSTRUMENT Co. 217 Sterner Mill Road, Trevose, PA 19053 Telephone No. (215) 355-8400 Fax No. (215) 355-1789 Email: office@thermalinstrument.com INSTALLATION, OPERATION INSTRUCTIONS FLOW SWITCHES 62-9FS & 600-9 FS 220VAC 110VAC 24 VDC Factory Set P a g e Effective Date 7/10/2008...
  • Page 2 62-9FS & 600-9 FS FEATURES  True mass flow for gases and liquids  All welded 316SS body standard  Special materials available for corrosion or abrasion resistance  Unobstructed flow path  Pipe sizes and fittings to suit applications ...
  • Page 3 INSTALLATION MODEL 600-9FS AND 62-9FS FLOW SWITCH #1& #2 PROVIDE OUTLINE DRAWINGS OF THE FLOW SWITCH, SHOWING FLOW CONNECTIONS IGURE AND MOUNTING DIMENSIONS. ALL FLOW WETTED PARTS ARE 316 STAINLESS STEEL. THE FLOW SWITCH CAN BE MOUNTED HORIZONTALLY OR VERTICALLY, HOWEVER, WHEN MOUNTED VERTICALLY FLOW DIRECTION MUST BE UPWARDS.
  • Page 4 OPERATION – MODEL 600-9FS AND 62-9FS WITH ALL CONNECTIONS HAVING BEEN COMPLETED AND TESTED, APPLY POWER AND ALLOW A TEN (10) MINUTE WARM UP PERIOD. CAUTION: FLOW AND TRANSDUCER MUST BE WIHTIN 50°C OF OPERATION TEMPERATURE BEFORE POWER IS APPLIED. SENSORS MAY BE DAMAGED IF TRANSDUCER TEMPERATUE IS LOWER THAN THIS LIMIT OR CALIBRATION WILL NOT BE ACCURATE.
  • Page 5 Figure #1 P a g e Effective Date 7/10/2008...
  • Page 6 Figure #2 P a g e Effective Date 7/10/2008...
  • Page 7 Figure #3 P a g e Effective Date 7/10/2008...
  • Page 8 Figure #4 P a g e Effective Date 7/10/2008...
  • Page 9 GENERAL PRECAUTIONS TO BE OBSERVED IN INSTALLING FLOWMETER WIRING When the Thermal Flowmeter or Probe is supplied with an explosion-proof condulet, it must be installed with approved wiring techniques. This calls for seals where the external wiring enters these condulets. In the case where we have a large condulet on a Probe with multiple connections, we will have a fitting with as large as a 1 2"...
  • Page 10 10 | P a g e Effective Date 7/10/2008...
  • Page 11 11 | P a g e Effective Date 7/10/2008...
  • Page 12 12 | P a g e Effective Date 7/10/2008...
  • Page 13 13 | P a g e Effective Date 7/10/2008...
  • Page 14 14 | P a g e Effective Date 7/10/2008...
  • Page 15 15 | P a g e Effective Date 7/10/2008...
  • Page 16 16 | P a g e Effective Date 7/10/2008...

This manual is also suitable for:

600-9 fs