Panasonic S-LINK SL-TPR4 Instruction Manual

Sensor & Wire-saving Link System S-LINK
Relay Output Terminal Unit
SL-TPR4, SL-TPR8
Thank you very much for purchasing Panasonic products. Read
this Instruction Manual carefully and thoroughly for the correct
and optimum use of this product. Kindly keep this manual in a
convenient place for quick reference.
1 OVERVIEW
This product is an ultra-small S-LINK relay output terminal unit
which permits relay replacement.
PART DESCRIPTION
2
● SL-TPR4 / 4 channel relay output type
4-core flat cable 0.6m long
Address setting switch
Setting switch section
Switch cap removed
condition
Transmission indicator (Green)
Relay removal key
2-mounting holes for M4 screws
● SL-TPR8 / 8 channel relay output type
4-core flat cable 0.6m long
Address setting switch
Setting switch section
Switch cap removed
condition
Transmission indicator (Green)
Relay removal key
2-mounting holes for M4 screws
PRECAUTIONS
3
Make sure that the power supply is off while wiring.
●
Switch on the power supply after confirming that the wiring is
●
correct. If the power supply is switched on when the wiring is
incorrect, there is a danger of malfunction or damage.
Do not use during the initial transient time (0.5 sec.) after the
●
power supply is switched on.
If power is supplied from a commercial switching regulator,
●
ensure that the frame ground (F.G.) terminal of the power
supply is connected to an actual ground.
Do not run the wires together with high-voltage lines or power
●
lines or put them in the same raceway. This can cause
malfunction due to induction.
A switch cap is fitted on the setting switch section. Remove
●
the cap at the time of setting. After the setting, make sure to fit
it back.
Use tweezers, etc., having a tip width of approx. 0.8mm to
●
operate the switches.
This product does not have a dust-proof or water-proof
●
construction. Do not use it in places having excessive water
vapor, dust, corrosive gas or where it may come in direct
contact with water or chemicals.
Make sure to fit the cover before use.
●
INSTRUCTION MANUAL
MJE-SLTPR No.0063-18V
Output hold setting switch
4-operation indicators (Orange)
output relays (4 relays)
PA-N Relay APAN3124
made by Panasonic
Corporation
Terminal block
DIN rail stopper
Output hold setting switch
8-operation indicators (Orange)
output relays (8 relays)
PA-N Relay APAN3124
made by Panasonic
Corporation
Terminal block
DIN rail stopper
Never use this product with a device for personnel protection.
･
In case of using devices for personnel protection, use products
･
which meet laws and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or
country.
Before touching this product, remove any electrostatic charges
･
that may be present on your body. There is a danger of this
product getting damaged due to the electrostatic charge.
4

SPECIFICATIONS

Type 4 channel relay output
Item Model No.
Supply voltage
(supplied from the S-LINK control unit or separate power supply)
75mA or less (when all outputs are
Current consumption
ON, excluding connected devices)
FAN-in
Relay contact 1a
・Nominal switching capacity : 250V 2A AC (resistive load)
・Min. switching capacity : 5V 1mA DC (Note 1)
Output
・Expected life: 100,000 operations or more
(per relay)
・Mechanical life: 20 million operations or more
Output relay turns ON when the output signal from the signal
Output operation
transmission line is ON.
Number of output points
Green LED (blinks to indicate the synchronization signal
Transmission indicator
transmission from the S-LINK control unit)
Operation indicator Orange LEDs (lights when the output relay is ON)
Output hold function
Ambient temperature 0 to +55℃ (No dew condensation), Storage: -20 to +70℃
Ambient humidity
Case: PC-ABS resin, Cover: Polycarbonate
Material
DIN rail stopper: POM, Relay removal key: POM
Cable
Weight
Accessories Cover: 1 pc., Switch cap: 1 pc., Relay removal key: 1 pc.
Note: 1) This value can change due to the switching frequency, environmental conditions, and desired
reliability level, therefore it is recommended to check this with the actual load.
5 OUTPUT CIRCUIT DIAGRAM (per channel)
Color code
+24Ｖ DC (Brown)
D (White)
G (Black)
0V (Blue)
S-LINK side Internal circuit
6 OUTPUT HOLD FUNCTION
The output state just before occurrence of an error can be stored
●
at the time of a shut-down on the signal transmission line.
Hold ON (output stored) or Hold Clear (output not stored) can be
●
set by the output hold setting switch.
Hold ON
Output hold
setting switch
Output stored
WARNING
8 channel relay output
SL-TPR4 SL-TPR8
24V DC±10%
130mA or less (when all outputs are
ON, excluding connected devices)
3
30V 2A DC (resistive load)
(at rated voltage, switching rate 20 operations/min.)
(switching rate 180 operations/min.)
4 points 8 points
Incorporated
35 to 85% RH, Storage: 35 to 85% RH
0.5mm 2 4-core flat cable 0.6m
approx 100g. approx 150g.
Output relay
SL-TPR4: Output 0 to 3
Output
SL-TPR8: Output 0 to 7
Output device side
Hold Clear
Output hold
setting switch
Output not stored