Related Manuals for Medic4All MiniGate VMG03
Summary of Contents for Medic4All MiniGate VMG03
- Page 1 FCC submission Product Manual October 21, 2004 Medic4All Ltd. POB 4222 Petach Tikva, Israel 49000...
- Page 2 Operation Manual MiniGate™ is an IP-based USB gateway. Plugging MiniGate™ into a standard USB port activates its software and displays data generated by Medic4All’s wireless vital signs monitors on the computer screen. With an Internet connection, measurement data can be sent directly and securely to a monitoring center and/or to a web medical file.
-
Page 3: Copyright Notice
Medic4All’s customer, without the written permission ® of Medic4All All other products are trademarks or registered trademarks of their respective holders and should be noted as such. -
Page 4: Table Of Contents
Connecting the MiniGW to the computer MiniGate initial activation and setup 14 MiniGate Daily usage 16 View measurements 16 Updating the Web measurements MiniGate Configuration 19 Configuring measuring devices Changing MiniGate password Associating the MiniGate to Medic4all Web Medical File 21... - Page 5 List of figures: Figure 1- “Choose language” window ............. 8 Figure 2- “welcome to the installation” window..........9 Figure 3- License agreement window ............. 9 Figure 4– Destination folder window............. 10 Figure 5 – Ready to Install window ............... 11 Figure 6 - File version conflict window ............
-
Page 6: Introduction
The MiniGate is responsible for accepting the measured data, and for sending it to the Medic4All call center medical file. On the local PC, the application provides the user with the ability to view the medical measurements and configure system parameters. Using the Internet, the user or his delegate (e.g., a physician) may view the measurements... -
Page 7: Installation
Preparing to install In order to install the MiniGate application, you need to have Administrator privileges on your Operating System. Make sure there are no old Medic4All programs installed on your PC. To start the installation, verify that you have the following parts:... -
Page 8: Installation Process
Installation process To install the Medic4All MiniGate application: Insert the Medic4All CD into the CD ROM and run the file: Medic4All MiniGate Setup.exe. The MiniGate setup screen opens; on top of this screen, the “Choose language” window appears. Figure 1- “Choose language” window In the language selection window, select a language and click Next. -
Page 9: Figure 2- "Welcome To The Installation" Window
Figure 2- “welcome to the installation” window Follow the instructions that appear in the “Welcome to the installation wizard” window and click Next. The “License agreement” window appears. Figure 3- License agreement window... -
Page 10: Figure 4- Destination Folder Window
Read the license agreement. If you wish to exit the installation, click Cancel. If you wish to continue with the installation of the MiniGate, mark √ in the and click Next. The “Destination folder” window appears. Figure 4– Destination folder window You can change the default destination folder that is presented in the window or you can use the default folder. -
Page 11: Figure 5 - Ready To Install Window
(see Figure 1). Figure 6 - File version conflict window The system finishes installing the MiniGate and opens the “ Installation complete” window. The “ Installation complete” window contains a “start Medic4All MiniGate” check box that is checked by default. - Page 12 (see MiniGate initial activation and setup). In order to terminate the installation without starting the MiniGate application, uncheck the “Start Medic4All MiniGate” checkbox and click Finish. Note: If you choose to continue and open the MiniGate application, refer to the activating the MiniGate application section.
-
Page 13: Minigate Operation
IDs. The user may change the MiniGate local password and define or update medical file settings. Every Medic4all MiniGate is initially set at the factory to work with its dedicated measuring device and is set with a default password. Therefore, at initialization, the user has to configure only user-specific WEB parameters for establishing the link to the patient medical file. -
Page 14: Minigate Initial Activation And Setup
Note: In case the PC does not recognize the MiniGW, try reentering the MiniGW. In case the problem is not solved, start the Windows Add New Hardware wizard or contact your Medic4all representative for further instructions. MiniGate initial activation and setup When first activating MiniGate, the user is required to associate, through he Internet, the MiniGate system to his call center medical file. -
Page 15: Figure 7 - Web Registration Window
Figure 7 - Web registration window In the web registration window, fill in your Web user ID and WEB password in the designated fields and click OK. If you do not have a web medical file, click Cancel. Remember, the Web user password is not the same Note: as the MiniGate password and it is case sensitive. -
Page 16: Minigate Daily Usage
following icon appears in the system tray: MiniGate Daily usage When activated, the MiniGate system application runs in the background without interfering with other PC programs. Usually you do not have to activate the system, except after installation, since it is automatically started when the computer is turned on. -
Page 17: Figure 8 - Minigate Authorization Window
Figure 8 - MiniGate authorization window the MiniGate password and Click Next. Enter Important: The MiniGW initial password is: m4a123 Note: Remember the MiniGate password is case sensitive. The MiniGate measurement viewer appears (see Figure 4... -
Page 18: Updating The Web Measurements
Figure 9 - Offline measurement View Updating the Web measurements While there is an active Internet connection, the measurements received by the MiniGate are transmitted automatically, once every 30 seconds, to the user’s medical file. If the Internet connection is down, the system stores the measurement in the local repository (see also View measurement) and waits for Internet connection to be established. -
Page 19: Minigate Configuration
MiniGate Configuration Configuring measuring devices To configure new sensors to the MiniGate: Verify the MiniGate is working (view the MiniGate icon in the system tray - see Activating the MiniGate application). Open the MiniGate menu by right-clicking the MiniGate icon in the system tray. -
Page 20: Changing Minigate Password
In the Add sensor window, enter the ID number of the sensor you wish configure and Click Add. Note: The sensor ID is an 8 character ID and usually appears on a sticker on the back of the sensor. The sensor ID identifies the sensor to the MiniGW and enables the MiniGW to communicate with the sensor. -
Page 21: Associating The Minigate To Medic4All Web Medical File
Enter the old MiniGate password and Click Next. The password is changed and the system generates change password confirmation. Associating the MiniGate to Medic4all Web Medical File To associate your MiniGate to your medical file, so measurements from your MiniGate will show on your Medical File:... -
Page 22: Figure 11 - Minigate System Tray Menu
Verify that the MiniGate is working (view the MiniGate icon in the system tray - see Activating the MiniGate application) Open the MiniGate menu by right-clicking the MiniGate icon in the system tray (see Figure 6). Figure 11 - MiniGate system tray Menu Select the Web Medical File Equipment Update option. - Page 23 In the web registration window, enter your Web user ID and Web password ID in the designated fields and click OK. Note: Remember that the Web user password is case sensitive. Click Next. The system updates the Web server and generates a confirmation message.
- Page 24 Specifications Environment Operating condition +10˚C to +40˚C / 30% RH to 85% RH Storage condition -10˚C to +55˚C / 30% RH to 85% RH Dimensions Approx. 95[W] x 15[H] x 25 [D] mm Weight Approx. 7g Power Supply/bat Power 5V up to 100mA powered from the USB interface Radio Frequency communication Frequency...
- Page 25 Contents: Operation Manual 2. MiniGate™ FCC Part 15 Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communication Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 26 This product warranty is void if the product has been repaired or altered in any way as to affect its use and operation as determined by the Company. This warranty is also void if the product has been subjected to abuse, misuse, negligence or accident.
Need help?
Do you have a question about the MiniGate VMG03 and is the answer not in the manual?
Questions and answers