Advertisement
Quick Links
Advertisement
Summary of Contents for Rio Flexon BTM-D1A
- Page 1 BTM-D1A Monitoring Ear Thermometer Product Instruction Manual...
- Page 2 1. Introduction of BTM-D1A - Ear Thermometer Key Pads & Functions (1) The Receiver Temperature Left Key Right Key OK Key Power Indicator Power Key ※ The instruction of the Keys and the Power Indicator: Ear Temperature Key: for the use of the ear temperature measuring Ok Key、Left Key、...
- Page 3 Armpit Temperature Status (2)The LCD Display of the Receiver Ear Temperature Elephant Indicator Indicator ℃/℉ Temperature Indicator High/Low Temperature Alarm Setting Wireless Armband Battery Transmission Indicator Indicator Receiver Battery Indicator (3) The Armband Temperature Sensor Power Indicator Power Key Battery Installation: Using a coin or screw-driver, turn counter-clockwise to open the battery cover.
-
Page 4: Operating Instructions
Operating Instructions (1)Ear Temperature Measuring: Step 1. Press "Ear Temperature Key" for 2 seconds until the "Elephant Indicator" and the "Ear Temperature Indicator" begin to flash. Step 2. When the "Elephant Indicator" stops flashing it has a full power supply. Then, insert the Ear Monitor into the ear of the patient. - Page 5 alarm setting procedures are as follows: Step1. High temperature setting: Press the “OK Key” for 2 seconds then the Receiver Beeps twice to get into the temperature alarm setting mode. The Display shows “HI” and the Default figures flashing on it. Step2.
- Page 6 xAbnormal Temperature Alarm: ®Alarm： The High/Low Temperature Alarm Setting of the Display will be flashing on the “HI” and “LO” and their related figures when the temperature of a patient out of the temperature alarm setting. That is, the “HI” and the figures are flashing and vice versa. The Receiver will “Beep, Beep, Beep, Beep”...
-
Page 7: The Instructions Of Indicators
3. The Instructions of Indicators Armband Power Indicator Light Status Flashing Green Normal 4 seconds each Orange Low Volt 4 seconds each Power Off One blink then power off Low Battery Alarm (1) Receiver Battery Indicator: Power Supply Status Receiver Battery Alarm sounds Indicator Full power supply... - Page 8 Poor Signal Warning ℃ 1. The Temperature Indicator shows “- - - ” on the LCD Display of the Receiver when failed to receive the signal from the Armband after turning on the Receiver and then it will Beep twice per 10 seconds. Please reset the Receiver to start receiving the signal from the Armband.
-
Page 9: Importance Precautions
4. Importance Precautions 1. This product is designed to function properly under the conditions of the surrounding ℃ temperature between 15 to 40 , and the relative humidity of 95% and lower. Please do not use this product when temperature and humidity is out of the ranges above. 2. - Page 10 Temperature Every 12 seconds transmission frequency ℉ ℉ Valid (96-104 ) (89-96 ) HI：35-42℃ LO：32-34.5℃ temperature alarm ranges Transmission 2.4 Ghz frequency Radio modulation technique Transmission 20 meters distance Armpit ±0.1℃ temperature precision ±0.2℃ temperature precision Notice : The changes or modifications not expressly approved by the party Responsible for compliance could void the user’s authority to operate the equipment.
- Page 11 General Agent :RIO FLEXON TECHNOLOGY CO., LTD 15 Fl, No 868-2 Chung-Cheng Rd, Chung Ho, Taipei County 0800 Customer Direct Line﹕0800-800306 Fax Number﹕02-82218198 E-mail:service@rio-flexon.com.tw http://www.rio-flexon.com.tw Attached behind the warranty card...
Need help?
Do you have a question about the BTM-D1A and is the answer not in the manual?
Questions and answers