Summary of Contents for Just Add Power Ultra HD IP
- Page 1 3G Standard Video Wall Manual - Just Add Power STANDARD VIDEO WALL MANUAL Revised 2019-01-01 © 2019 Just Add Power – All rights reserved – Unauthorized use or disclosure prohibited – Last updated Jan-19...
-
Page 2: Table Of Contents
Programming ..........................9 Telnet ................................10 Command Format ..............................10 Set Rotation ................................11 Set Size & Position ..............................12 Set Horizontal Mirror ............................13 Set Bezel Measurements ............................14 justAPI ................................15 Just Add Power – Last updated Jan-19... -
Page 3: Introduction
3G Standard Video Wall Manual - Just Add Power Introduction Just Add Power Ultra HD over IP 3G Receivers have built-in video wall scaling. In a Just Add Power distributed system, a source can be viewed as a single screen and video wall at the same time. -
Page 4: Requirements
3G Standard Video Wall Manual – Requirements • One Receiver per Display in the video wall A computer connected to the same network as the switch running Just Add Power devices • • WebUI access to the Just Add Power devices o Set a Static Route on the router to allow Layer 3 communication o Alternatively, set the computer’s IP details manually so the Default Gateway is equal to the IP Address of... -
Page 5: Content Scaling
Content Scaling Just Add Power Receivers create a video wall by scaling the video content to a size that matches the full wall. This means that it does NOT take into account the aspect ratio or native resolution of the picture that it is sending. -
Page 6: Other Aspect Ratios
To maintain 16:9 Aspect Ratio on other Aspect Ratio layouts, content must be specially designed before being sent to a Transmitter. Content that has been compressed horizontally on a 16:9 Display will scale properly when shown at 32:9 across a 1x2 wall. Just Add Power – Last updated Jan-19... -
Page 7: Rotated Displays
Rotated Displays Just Add Power 3G Ultra HD over IP devices add the ability to rotate the video output clockwise at 90, 180, or 270 degrees. Paired with video wall, this gives the ability to make portrait and flipped video walls. -
Page 8: Setup
3G Standard Video Wall Manual – Setup 1. Configure the switch and all Just Add Power devices. 2. Set the screens in the video wall to watch the same source. 3. Access the web interface of one of the Receivers in the video wall. All configuration is done through a single webUI. - Page 9 Position 1. 15. If unsure which Receiver is attached to the top-left Display, click the OSD On button. Each display will show text with the MAC address and IP address of the Receiver. Just Add Power – Last updated Jan-19...
- Page 10 18. Repeat Step 17 for each Receiver in the video wall. 19. Congratulations! Just Add Power Receivers are setup for a Standard Video Wall. 20. If the video does not look aligned and synchronized, check these settings outside the Just Add Power devices: •...
-
Page 11: Programming
– 3G Standard Video Wall Manual Programming To change the layout of a Standard Video Wall live, communicate directly to the Just Add Power Receiver connected to the Display. To modify an entire wall simultaneously, connect to multiple Receivers and send the commands simultaneously. -
Page 12: Telnet
Set Bezel measurements. Uses: Outside Width, Outside Height, Video Width, Video Height. Set zoom level beyond size & position. Uses: Horizontal Scale, Vertical Scale. Shifts the picture. Uses: Horizontal Pixel Shift, Vertical Pixel Shift. Just Add Power – Last updated Jan-19... -
Page 13: Set Rotation
– Clockwise video rotation angle. 0, 90, 180, 270 $ROT Examples Rotate video 90 degrees clockwise (display should be rotated 90 degrees counter-clockwise) vw –r 90 Rotate video 180 degrees clockwise (display should be upside-down) vw –r 180 Just Add Power – Last updated Jan-19... -
Page 14: Set Size & Position
– column position of this Receiver. Integer 1 or greater. Less than or equal to $TC. Examples Row position 1, column position 1 of a 2-row, 2-column wall vw –l 2,2,1,1 4-row, 5-column wall with the Receiver in row 2, column 3 vw –l 4,5,2,3 Just Add Power – Last updated Jan-19... -
Page 15: Set Horizontal Mirror
Set Horizontal Mirror Set horizontal mirroring. Uses: On or off. vw –m Variables – y for mirror. n for standard. Examples Enable horizontal mirror vw –m y Disable horizontal mirror vw –m n Just Add Power – Last updated Jan-19... -
Page 16: Set Bezel Measurements
– Outside Height measurement. Integer less than 65000. – Video Width measurement. Integer less than 65000. – Video Height measurement. Integer less than 65000. Examples Set Bezel measurements to OW: 4413, OH: 2550, VW: 4300, VH: 2425 vw –b ow:4413,oh:2550,vw:4300,vh:2425 Just Add Power – Last updated Jan-19... -
Page 17: Justapi
– 3G Standard Video Wall Manual justAPI A RESTful API Full information on justAPI is available at https://justaddpower.docs.stoplight.io/ Just Add Power – Last updated Jan-19...
Need help?
Do you have a question about the Ultra HD IP and is the answer not in the manual?
Questions and answers