Advertisement
Quick Links
Advertisement
Summary of Contents for Sunion MD-150M
- Page 1 Users’ Manual Product: Mifare USB Reader Model: MD-150M...
-
Page 2: Federal Communication Commission Interference Statement
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 3 Any third party is forbidden strictly to copy, edit, modify or quote the contents of this document without written approval from SUNION electronic Corp. SUNION’s products are not authorized for use as critical components in life support devices or systems.
- Page 4 MD-150M User Manual I. MD-150 M Reader Specification 1 . Reader Specification MD-150M Part Number 13.56 MHz RF Transmit Frequency Mifare_UltraLight Mifare_One(S50) Mifare_One(S70) Supported Transponder Mifare_Pro(X) Mifare_DESFire 25~30 mm Maximum Reading Range* 150 ms Reading Times DC 5V/ 500mA Regulated...
- Page 5 MD-150M/MK-1500M User Manual 3. Dimension 4.275mm 70mm 孔2mm 孔2mm 66.875mm - 4 -...
-
Page 6: Communication Protocol
(COM PORT) ; Procedure of user can is it communicate to go on through this communication between mound and copies of machine. MD-150M are using t he international S tandard UART communication for mat, and support RS-232 interface with communication parameters set to 9600.N.8.1. - Page 7 MD-150M User Manual III. USB Reader Command list Function Code Description Page "A0" Switch to Stand-Alone Operation "A1" Read card and acquire card ID "E1" Acquire model name and firmware version "E2" Reset reader "K0" Read data in specified page/block "K1"...
- Page 8 MD-150M/MK-1500M User Manual IV. USB Reader command description “A0” (Switch to Stand-Alone Operation) Controller send： “S” “A” “0” USB Reader responds： “s” “A” “0” data Function description: (1) This function code is able to switch the reader to the “Stand-Alone Operation”.
- Page 9 MD-150M User Manual “A1” (Read card and acquire card Controller send： “S” “A” “1” USB Reader responds： “s” “A” “1” data Data description: (1) The format of “data” will be: Card type (1 byte) + Card ID (16 byte). (2) Card number is “0” ～ “9” ， “A” ～ “F” 。 ex. "00000000003EA88F"。...
- Page 10 "s07E1" + STX + "V1.01 USB Reader" + ETX + BCC Description： The current firmware version is: V1.01and the model name is: USB Reader. Sunion reserved the right to update firmware at any time without prior notice. - 9 -...
- Page 11 MD-150M User Manual “E2” ( Reset reader) Controller send： “S” “E” “2” USB Reader responds： “s” “E” “2” data Function description: 1. Use this function to reset USB Reader. 2. If “data” value responded is “Y” means the set up is successful, “N” means failed, repeated or no data.
- Page 12 MD-150M User Manual “K0”( Read data in specified page/block) Controller send： “S” “K” “0” DATA USB Reader responds： “s” “K” “0” data Data description： 1. “DATA” should be entered as: Card type (1 bytes) + Page/Block number (2 bytes). 2. When Read Mifare Card, Card type is “M ” + Page/Block number；The page/block number is fixed to 2 bytes.
- Page 13 MD-150M User Manual “K1” (Write data into specified page/block) Controller send： “S” “K” “1” DATA USB Reader responds： “s” “K” “1” data Data description： DATA should be entered as cars type, page/block number and the information you want to input, just as follow: Card type (1 byte) + Page/block number (2 bytes) + Information (16 bytes).
- Page 14 MD-150M User Manual “K2” (Choose want to use Key) Controller send： “S” “K” “2” DATA USB Reader responds： “s” “K” “2” data Data description： 1. “DATA” should be compare with A,B Key, sector number you want to lock, just as follow: Card type (1 byte) + Page/block number (2 bytes) 2.
- Page 15 MD-150M User Manual “K3” (Set A,B Key value of 32 Sector groups ) Controller send： “S” “K” “3” DATA USB Reader responds： “s” “K” “3” data Data description： 1. DATA should be entered as cars type, Sector group and the information you want to input, just as follow:Card type (1 byte) + ［Sector group(2 bytes)］...
Need help?
Do you have a question about the MD-150M and is the answer not in the manual?
Questions and answers