Advertisement
Quick Links
Acknowledging Special Precautions and the FCC Industry Canada Notice Cautions
Modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
FCC compliance Information
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received.
Including interference that may cause undesired operation.
Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device,
Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio Frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
B/T GPS RECEIVER
(BGP-2000)
OPERATING GUIDE
J Communications Co., Ltd.
Advertisement
Summary of Contents for J Communications Co., Ltd. BGP-2000
- Page 1 B/T GPS RECEIVER (BGP-2000) OPERATING GUIDE Acknowledging Special Precautions and the FCC Industry Canada Notice Cautions Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance Information This device complies with part 15 of FCC Rules.
-
Page 2: Getting Started
Navigating freely without wire connection to host mobile devices. 3. Prepare to use you BGP-2000 Receiver To help you begin to use your BGP-2000 receiver, read this user guide in the first step. This user guide explains the detail how BGP-2000 operates, functions, and common features of the BGP-2000. - Page 3 Or, might need at least 3 to 5 minutes from a completely restart-state, for example, flying a distance over 500 kilometers from initial origin. BGP-2000 uses the satellite signals to calculate an exact geodetic location through triangulation method, contained in 10 meters CEP accurateness devoid of Selective Availability (SA), which is good enough for general location awareness purposes.
- Page 4 Only use the charger supplies with the BGP-2000. Use other charger can damage the BGP-2000 and even dangerous at the risk of explosion. Do not expose BGP-2000 to high temperatures higher than 85C such in car under direct sunshine. Expose BGP-2000 to high temperatures environment can not only shorten the life of electronic devices and melt or drape certain plastics, but also can damage the battery and even dangerous at the risk of explosion.
- Page 5 Symbol : Blue LED indicates Bluetooth pair/connect status Flashing every 1 second : BGP-2000 just power-on and waiting for pair/connection Flashing every 2 second : BGP-2000 is connected and paired with the host Symbol : Green LED light indicates GPS status Constant on : When BGP-2000 just power on, attempting to fix a position.
- Page 6 Operation Guide Before using the BGP-2000, first make sure to prepare following steps are ready for operation. The GPS application software is correctly installed in the host platform(s) The BGP-2000 is fully power charged Check the Bluetooth is ON in the host.
- Page 7 [ Connection with HP Ipaq Series] (1) Tap Bluetooth icon in the task bottom bar. (2) Tap “Bluetooth Manager”icon in the Bluetooth general screen. (3) Click “New” at the bottom bar (4) Bluetooth connection wizard starts. Click “Next”...
- Page 8 (5) Click :Next” (6) Click “BGP2000” (7) Select “SPP slave” of device selection and click “Next”. (8) Connection shortcuts were successfully created. Click “Finish”.
- Page 9 (9) Connection was successfully established with Bluetooth GPS receiver on SPP slave. (10) To connect with BT GPS, double click “BGP2000 SPP slave” icon. (11) Click “Active Connections”. You will see the connection status.
- Page 10 [NOTE] (1) If you click security in the screen (07), you will be required to enter passkey to establish a paired relationship between devices. This is required at the first time only once. (2) Enter “0000” (Arabic numeral 0) as the passkey and click “enter” or “OK”...
-
Page 11: Troubleshooting
Caution : Do not use other charger to charge the BT GPS. Troubleshooting The solutions to some common problems 1. Sometimes, it took everything is alright, but you can not connect to BGP-2000. You should try to delete the old BGP-2000 icon on your Bluetooth manager software, and re-charging again.