Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Floeter AirBoy Nano3
- Page 1 nano3 - OPERATING INSTRUCTIONS...
-
Page 2: Table Of Contents
OPERATING INSTRUCTIONS Contents Contents Safety guidelines Air cushion types Machine overview Technical data Buttons introduction Accessories Operating device Operating setting details Parameter setting guidance Maintenance Notes Consumables and abrasion accessories declaration Failure Code Options and expandability Support and Service Document version 27.11.2018... -
Page 3: Safety Guidelines
All persons who use this machine must be familiar with the content of these operating instructions and must carefully follow the safety guidelines. FLOETER shall not be responsible for damage resulting from improper use of the machine or non-observance of the safety guidelines. -
Page 4: Air Cushion Types
OPERATING INSTRUCTIONS Air cushion types Our standard version – Polyethylene 20 µm or Bio (home-compostable) Type 7.1 AirWave air cushion filler 100 x 210 mm Ideal for filling small voids and for use as an intermediate layer Type 8.3 AirWave wrapper 420mm 4 chambers 4 chambers for use as an intermediate layer, wrapping, and envelope... -
Page 5: Machine Overview
OPERATING INSTRUCTIONS Machine overview 1. AC power cable 6. Tension column B 11. Puller A 2. Power switch 7. Roll film tension 12. Sealing wheel B 3. Control panel 8. Air nozzle 13. Conveyor wheels C/D 4. Feeding roller 9. Protecting cover A 14. -
Page 6: Buttons Introduction
OPERATING INSTRUCTIONS Buttons introduction 1. Temperature "+" 01~30 level 2. Temperature "-" 30~01 level 3. Air Volume "+" 01~40 level 4. Air Volume "-" 01~40 level 5. Start / Enter Film (press long time) 6. Pause / Adjust time (press long time) Accessories Name Quantity... -
Page 7: Operating Device
OPERATING INSTRUCTIONS Operating device 1. Turn on the power switch Connect the power cable and turn on the power switch 2. Load in the air cushion film Load the film roll into the feeding roller and pass the film through with the air channel side down, pull film in from the right side of tension column A, then pull out from the middle of guide tension column B and roll film tension. - Page 8 OPERATING INSTRUCTIONS Pull out from the middle of guide tension column B and roll film tension 3. Feeding the film onto the air nozzle Open the air channel and put film into air nozzle to pass through the air channel until the film is 1cm behind the wheels.
- Page 9 OPERATING INSTRUCTIONS 4. Start film Press the “start” button to start the feeding of the film and check the air volume and the sealing result. Adjust the temperature and air volume according to the desired results. Once the sealing result and volumes are perfect, you can preset working time and enter automatic working mode.
-
Page 10: Operating Setting Details
OPERATING INSTRUCTIONS The corner of the film can be cut at an angle to make it easier to fit the film over the air nozzle. Operating setting details 1. Temperature setting is on the left side of panel. Pressing the “+” button increases the temperature; pressing the “-” button decreases. -
Page 11: Parameter Setting Guidance
OPERATING INSTRUCTIONS Parameter setting guidance Temperature Value Setting: 1. Depending on the workplace temperature If the workplace temperature is around 30ºC and the AirWave Standard film with a thickness of 20μm is in use, then the reference temperature is: T=14. AirWave Standard film (20µm): T=14 AirWave Bio film (20µm): T=10 2. -
Page 12: Maintenance Notes
OPERATING INSTRUCTIONS Air volume setting Specification of film AirWave type 7.1 - 210x100mm AirWave type 8.3 - 420mm Reference data 1. The reference air volumes as above are for the air cushion films with the thickness of 20µm. 2. Correct air value will give better seal performance. 3. - Page 13 OPERATING INSTRUCTIONS Using the screwdriver unscrew the screws of blade and change them. Wheels clearance • The sealing quality will be effected if there are residue of air cushion film in the conveyor wheels, please clean them regularly. • Sealing wheels abrasion The middle round of the sealing wheels is easily roughened.
- Page 14 OPERATING INSTRUCTIONS Tear off the sealing belt in the middle of sealing wheels and replace it. • High temperature belt abrasion Please replace the high temperature belt when there are abrasions, the heating unit, the conveyor wheels and the sealing wheels will fail if the high temperature belt is worn and not replaced.
- Page 15 OPERATING INSTRUCTIONS Take out the colloidal pins in the two side of high temperature module and replace the high temperature belt...
-
Page 16: Consumables And Abrasion Accessories Declaration
OPERATING INSTRUCTIONS Consumables and abrasion accessories declaration The knife and Teflon bands are abrasion accessories and need to be changed after continuous use of the machine. Wearing parts Knife / Blade High temperature belt Pins Conveyor Wheel A Heating piece Heating piece fixation module... -
Page 17: Failure Code
OPERATING INSTRUCTIONS Failure Code Each time the power supply of this device is turned on, the device will do the self-testing. At that time the motor will drive the conveyor wheel to complete the self-testing. Please contact with our customer service center and we will solve these problem as soon as possible. - Page 18 OPERATING INSTRUCTIONS Warning Mot - Air blowing module failure If the film is not being sealed very well or the film is perforated please check the temperature value and adjust appropriately. If it is not working, please check whether the high temperature and sealing wheel B are scuffed. Turn on the power switch of device, the screen is completely blank and the device does not have any action (air blower and conveyor wheels).
- Page 19 OPERATING INSTRUCTIONS Common failure and solutions Item Failure Reason analysis Solution phenomenon Air leakage Temperature Increase value is too low temperature value Sealing is wide Temperature Lower and thin value is too high temperature value Under-inflation Air volume value Increase air is too low volume value During operation,...
-
Page 20: Options And Expandability
Roll trough For an easy storage of endless rolled sheets in optimum height Contact: FLOETER Verpackungs-Service GmbH Robert-Bosch-Str. 17 71701 Schwieberdingen Germany tel: 0800 FLOETER (free within Germany) e-mail: info@floeter.com tel: +49 (0) 71 50 / 923 96-0... -
Page 21: Support And Service
OPERATING INSTRUCTIONS Support and Service You need support, advice or do you have any questions? We are here for you: www.floeter.com/en/support/ FLOETER Verpackungs-Service GmbH Robert-Bosch-Straße 17 71701 Schwieberdingen Germany tel.: +49 (0) 7150 / 923 96 - 0 Info@floeter.com www.floeter.com...