Related Manuals for Monster Central Revolution 200
Summary of Contents for Monster Central Revolution 200
- Page 1 S I M P L E A D V A N C E D H O M E T H E A T E R A N D L I G H T I N G C O N T R O L I N S T R U C T I O N M A N U A L...
-
Page 2: Table Of Contents
Copy Option 1: Create Secondary Controller – Entire REVOLUTION 200 ....... -
Page 3: How To Set Up Lighting
HOW TO SET UP LIGHTING PROGRAMMING TIME AND DAY To set the time and date: OPERATING BEHAVIOR FOR Z-WAVE / LIGHTING FUNCTIONS Press and hold the button for 3 seconds without ‘MONSTER’ highlighted. (If you have not shift previously used the REVOLUTION Remote Control Setup Wizard, the on-remote screen will It’s highly recommended you read the Glossary of Terms and this section before reading any display the message, “Use Web Setup or Press OK to Use Remote Setup”). -
Page 4: Creating A Z-Wave Network Of Modules
CREATING A Z-WAVE NETWORK OF MODULES The menu changes and Add is highlighted. Use the button to highlight Delete instead. Press the button. A network is the sum total of Z-Wave modules you have paired with your REVOLUTION remote where each module is referred to as a “node.” You can add and delete nodes from your network. The remote’s LCD screen display reads, “Press pairing button on device.”... -
Page 5: Customizing The All On/Off Feature
Customizing the ALL ON/OFF Feature The LCD screen displays, “Include in All ON/OFF” and awaits a signal from the module you wish to include. Hold the remote near the module and press the pairing button on the module. Unless you customize the behavior of the ALL ON/OFF feature, then by default, the remote will attempt to turn on or off, all modules it finds on your Z-Wave network based on the current state When the remote receives the signal from the module, the remote’s LCD screen will briefly read, of toggle. -
Page 6: Managing Scenes
MANAGING SCENES The menu changes and Setup is highlighted. Use the button to highlight Rename instead. Press the button and the remote lists all scenes. Scenes are collections of nodes you specify as related to one another in a way that’s meaningful Use the button to highlight the scene you wish to rename and press the button. -
Page 7: Controlling Scene Controllers (Monster Illuminessence Scene Controllers)
The menu changes and Setup is highlighted. Use the button to highlight Delete Scene How to Delete / Remove a Scene Controller from your Z Wave Network instead (a fourth menu choice not displayed among the first three). Press the button. -
Page 8: How To Remove A Scene From A Button On The Scene Controller
scene you chose in the previous step, press the OK button and hold the remote 3” to 5” from Use the button to highlight Update Control. the scene controller. The remote displays the message, “Select Scene Controller” followed by Controller #1 The remote displays the message, “Sending”... -
Page 9: How To Remove An Event
#5 for additional event scheduling. Controller Swap – All network, device, Destination controller How to Enable / Disable an Event Entire REVOLUTION 200 group, and scene becomes primary information (includes remote. Source When you enable an event you’ve already added, the remote will perform the event at the time... -
Page 10: Preparing The Destination Controller To Receive Data
Performing this command copies all node information but does not copy any scenes. Copy Option 1: Create Secondary Controller – Entire REVOLUTION 200 On your source remote, follow the same steps 1 to 4 you just performed on your Destination On your source remote, follow the same steps 1 to 4 you just performed on your Destination controller (see Preparing the Destination Controller to Receive Data). -
Page 11: Managing Network Setup
MANAGING NETWORK SETUP If the copy succeeds, the source remote screen will say SUCCESS. Otherwise, it will read FAIL or EMPTY (to specify the network has zero nodes). At the network level, there are four operations the remote can perform: Network Reset, Network Recovery, Network Update, and Remove Fail Node. -
Page 12: Glossary Of Terms
Controlling Thermostats GLOSSARY OF TERMS Your REVOLUTION remote can control any Z-Wave enabled thermostat. To find the pairing button Z-Wave: Z-Wave uses reliable, low power radio waves to control all aspects of your home for your Z-Wave enabled thermostat, consult your manufacturer’s manual. wirelessly: lighting, climate control, safety and security, home entertainment, energy conservation, remote monitoring, and more. - Page 13 7251 West Lake Mead Blvd. Las Vegas, NV 89128 Monster, the Monster logo, Revolution 200, Monster Central, and the Monster Central logo are trademarks or registered trademarks of Monster Cable Products, Inc. or its subsidiaries in the United States or other countries.
Need help?
Do you have a question about the Revolution 200 and is the answer not in the manual?
Questions and answers