Subscribe to Our Youtube Channel
Related Manuals for MeiTrack T466G
Summary of Contents for MeiTrack T466G
- Page 1 MEITRACK Driver Fatigue Monitor System User Guide MEITRACK Driver Fatigue Monitor System User Guide Applicable Model: T466G...
- Page 2 MEITRACK Driver Fatigue Monitor System User Guide Change History File Name MEITRACK T466G Driver Fatigue Monitor System User Guide Model T466G Creation Date 2018-12-13 Update Date 2019-01-30 Subproject Product User Guide Total Pages Version V1.1 Confidential External Documentation Copyright © 2019 Meitrack Group All rights reserved.
-
Page 3: Table Of Contents
1 Copyright and Disclaimer ............................- 4 - 2 Product Introduction ..............................- 4 - 2.1 Brief Introduction ............................- 4 - 2.2 T466G System Scheme Diagram ......................- 4 - 2.3 Product Functions ............................- 5 - 2.4 Function Description ............................. - 5 - 3 Product Specifications ............................... -
Page 4: Copyright And Disclaimer
The user manual may be changed without notice. Without prior written consent of Meitrack Group, this user manual, or any part thereof, may not be reproduced for any purpose whatsoever, or transmitted in any form, either electronically or mechanically, including photocopying and recording. -
Page 5: Product Functions
2.4 Function Description The T466G driver fatigue monitor system can be used by logistics companies and long-distance bus companies to detect a driver's fatigue state and provide an early voice warning. This will help prevent accidents in a timely manner, protect fleet companies' properties, and ensure driver safety. -
Page 6: Product Specifications
2 digital inputs and 1 analog detection input (0–30 V; selectable positive, negative, and analog detection inputs) 1 output 1 USB port 1 1-wire interface (set to an output or a negative input) 1 output (voltage: 5V) Copyright © 2019 Meitrack Group All rights reserved. - 6 -... -
Page 7: Fatigue Sensor Specifications
Cable 150 cm (length) 4 T466G and Accessories 4.1 T466G T466G Driver Fatigue Monitor sensor Bracket 4.2 T466G standard accessories: T466G tracker (internal and external antenna version is optional) L wrench Hexagon screw CD download card ... -
Page 8: T466G Installation
Maximum current for output low level (valid): 500 mA Set the PWM output (output time and adjustable pulse width). Connect to an external relay to remotely cut off the vehicle fuel cable or Copyright © 2019 Meitrack Group All rights reserved. - 8 -... -
Page 9: T466G Connection
5.2 T466G Connection T466G has a connector for easy connected with the fatigue driving sensor. Two long red and black I/O wires are used to connect the power supply of fatigue driving sensor. Due to the large power consumption of the sensor, it is easy to exhaust the car battery, the long red line is connected with ACC by default to power the sensor. -
Page 10: Testing
LED indicator is on, it means that the Monitor is installed normally and works properly. Ensure that the lens and the green LED indicator are vertical. The dashboard of trucks and buses is low, so you should install the Monitor on a higher location around the dashboard. Copyright © 2019 Meitrack Group All rights reserved. - 10 -... -
Page 11: Dip Switch Introduction
But the alert time of distraction and closing eyes will be different. The DIP switch is at the back of the Monitor, shown in the following figures. The switch will be pushed to the off position before delivery. Copyright © 2019 Meitrack Group All rights reserved. - 11 -... -
Page 12: Meitrack Manager Configuration
7.1 Setting the GPRS Event On the Event tab page, locate Driving Behavior, and select GPRS. When the Monitor detects an alert, a GPRS event will be sent to the MS03 tracking platform. Copyright © 2019 Meitrack Group All rights reserved. - 12 -... -
Page 13: Setting The Fatigue Driving Function
MEITRACK Driver Fatigue Monitor System User Guide 7.2 Setting the Fatigue Driving function Fatigue Driving Function Setting is only available for the Driver fatigue monitor sensor. When you restore the T466G to factory settings, the default parameter of this function cannot be restored. -
Page 14: Gprs Protocol About Alert Event 114
04: Distraction alert 180704002340_Yawning.jpg. 05: Absence alert 06: On Phone Call alert 07: Smoking alert 08: Yawning alert C: indicates the additional alert information. Copyright © 2019 Meitrack Group All rights reserved. - 14 -... -
Page 15: Ms03 Platform
10 MS03 Platform T466G Driver fatigue monitor system, real-time management and monitoring of the equipment through MS03 platform. In addition to basic MS0 functions: monitor vehicles, people, and objects equipped with trackers in real time on web pages. -
Page 16: Querying Driver Fatigue Time Statistics Reports
Expiry date: year-round UY = Unit of Trackers x Years 10.2 Querying Driver Fatigue Time Statistics Reports To view alert statistics information during different time periods, choose Reports, and click Fatigue driving time statistics. Copyright © 2019 Meitrack Group All rights reserved. - 16 -... -
Page 17: Querying Driver Fatigue Trip Statistics Reports
To view alert statistics information during different trips, choose Reports, and click Fatigue driving trip statistics. 10.4 Querying Driver Fatigue Mileage Statistics Reports To view alert statistics information per 100 km, choose Reports, and click Fatigue driving mileage statistics. Copyright © 2019 Meitrack Group All rights reserved. - 17 -... -
Page 18: Querying Alert Reports
MEITRACK Driver Fatigue Monitor System User Guide 10.5 Querying Alert Reports To view all alert events detected by the T466G, choose Reports, and click Event Report. 10.6 Querying Alert Photos To view all alert photos captured by the T466G, choose Reports, and click Photo Report.
Need help?
Do you have a question about the T466G and is the answer not in the manual?
Questions and answers