Princeton Tec FUEL Operating And Maintenance Instructions

ENGLISH
Battery Installation – See Battery Installation Diagram
• 3 AAA
• Alkaline (LR03)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and
recommends recycling batteries. For more information
about battery recycling, please go to:
www.batteryrecycling.com
To install the batteries, use the tool on the headband to
unlatch the door. Open the Fuel case by popping the
door latch over the catch and rotate the door open.
Install three AAA batteries according to the polarity
markings on the inside of the cabinet. Observe proper
battery polarity when installing the batteries. Improper
installation of the batteries will damage the light and
void the warranty.
Rotate the door to the closed position, squeeze the
body between your forefingers and thumb to snap the
door latch over the catch.
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry
types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Rechargeable NiCad or NiMH batteries may
result in reduced brightness due to lower nominal
voltage.
Switch Operation – See Switch Operation diagram
Modes (High, medium, low and flash) are selected by
pressing and releasing the button within 1.5 seconds of
the previous button press.
There are two ways to turn the Fuel off. You can cycle
through the modes until you reach off, or if more than
two seconds has passed since the previous button
press the next press of the button will turn the light off.
Power Consumption
Refer to the burn time chart for performance data for
different battery types and mode settings.
**Princeton Tec calculates total burn time as the time it
takes for the light source to produce a minimum of 0.25
lux at 2 meters. 0.25 lux is about the equivalent of a full
moon on a clear night.
**The times listed in this chart assume you start with
fresh batteries and use only one mode.
Troubleshooting
If the Fuel fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
Figure 1 – Switch Operation
press 1x = High
press 2x = Med
press 3x = Low
press 4x = Flash
4 Ultrabright
* Princeton Tec calculates total burn time as the time it takes for the light source to produce a
minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
* Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte
minimale Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa
der Beleuchtungsstärke des Vollmonds in einer klaren Nacht.
* Princeton Tec définit la durée totale d'éclairage comme le temps nécessaire à la source
lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la
luminosité d'une pleine lune dans un ciel nocturne dégagé.
Figure 2 – Battery Replacement
1
Use tool on headstrap to open battery compartment
Utilisez l'outil attaché à la sangle de la frontale pour
ouvrir le compartiment des piles.
Verwenden Sie zum Öffnen des Batteriefachs das
am Kopfband befestigte Werkzeug.
3
* The times listed in this chart
assume you start with fresh
batteries and use only one mode.
* Les durées mentionnées dans le
présent tableau sont calculées sur
la base de l'utilisation de piles
neuves et d'un seul mode d'éclairage.
* Bei den in der folgenden Tabelle
aufgeführten Zeiten wird
vorausgesetzt, dass Sie neue
Batterien und lediglich eine
Leuchtstärke verwenden.
• Check the light for water contamination on the
circuit board. The light will resume normal
operation once the water is shaken or blown out
and the light is left open until completely dry. If the
light has been contaminated with salt water, flush
the unit with fresh water and dry as described
above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to
be free from defects in workmanship and materials
under normal use for 5 years. This warranty covers all
of the component parts of the product except batteries.
This warranty does not cover deterioration due to
normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair.
Princeton Tec will repair or replace parts which are
defective in workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton
Tec are the only facilities authorized to repair the
product. After (3) unsuccessful attempts (within the
warranty period) to repair the product, you have the
right to elect replacement of the product or a refund of
the purchase price less allowance for use of the
product. NO INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARE INCLUDED IN THIS WARRANTY.
(Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitations or exclusions may not apply to you.) This
Opération de commutation
146H
LOW
LEDs
DISTANCE (Meters)
Remplacement des piles
2
4
Power Level
Battery
Type
Low Med High
3 AAA
Alkaline
Cells
warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
Return Policy
If your light fails to operate, follow these simple steps:
1) Check batteries. Replace if necessary.
2) Contact Princeton Tec customer service at
800-257-9080 to request an RMA number to send your
light in for repair or replacement. No warranty repairs
will be accepted without an RMA number.
3) Return the light without batteries to: Princeton Tec,
5198 Rt. 130, Bordentown, NJ 08505. Postage due
and freight collect items will not be accepted.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2013 Princeton Tec
Betriebsartenschalter
50H
HIGH
90H
MED
120H
FLASH
28 37
Einlegen der Batterien
Output Overall
Distance (m) Burn Time (Hours)
Flash
28 146
37 90
52 50
52 96
52