NightBalance Sleep Position Trainer Manual

01 SPT
On/off-button.
Port for charger and USB cable.
Indicator light.
04 Torso strap
01 Center the pocket on front of your torso,
just below the chest.
02 Pull the strap through the buckle and fasten with Velcro.
05 Sleeping with the SPT
Falling asleep period
01 Fall asleep in any position you prefer.
02 The 30 minute falling asleep period starts once
you switched the SPT on and you lay down.
06 Reading out sleep data
Make sure the SPT is switched on.
07 Switching off
hold
Press and hold until the white light stops
blinking (3 blinks).
A. SPT Comfort Program
The SPT Comfort Program consists of three fases.
01 Analyse fase
Day 1 2 3 4
Feedback
0 %
01 Analyse fase
(night 1-2)
No vibrational feedback, only
measures % of time slept on
your back.
C. SPT Software
01 Place the installation USB-stick or download
the SPT Software from the website:
nightbalance.com/support/software
D.
Legend for LED light
Green (slow blinking)
Orange (slow blinking)
Red
Blue (blinking)
White (blinking)
E.
Legend for LED light
Green
Green (blinking)
Orange (blinking)
Red
Pink
The Sleep Position Trainer (SPT) by NightBalance
The SPT is a small and light medical aid for the treatment of positional apnea. The SPT is worn around
the chest with a comfortable and ergonomic torso trap. It gently trains you by softly vibrating when you
sleep on your back, reminding you subconsciously to switch to a different sleeping position. This way
apnea is prevented which helps you feel more refreshed and energetic during the day.
02 Switch on
01 Press
02 The indicator light (LED light) slowly blinks
green when the SPT is switched on.
03 Position the SPT with the arrow facing up and
towards you into the pocket.
During sleep
01 After the falling asleep period the SPT starts with vibrational feedback.
02 The SPT adjusts the vibrational intensity to your sleeping behavior.
03 Turn over from your back when the SPT vibrates.
press 1x
Number of vibrations during the past night
Press once and count the number of blue blinks.
08 Charging
Orange: Charge the SPT with the charger, or by connecting it to your computer with the USB cable.
02 Build-up fase
5 6 7 8 9
02 Build-up fase
(night 3-9)
Gradual build-up of vibrational
feedback, decrease in % of time
slept on your back.
02 Install and start the software.
during use
Ready for use.
The device needs to be charged for the next night.
Go to nightbalance.com/support
Number of vibrations during the past night.
Number of times on your back during the past night.
during charging
Fully charged and ready for use.
Charging, but ready for use.
Charging, battery still low.
Go to nightbalance.com/support for troubleshooting.
Warning: Do not disconnect the device from the computer.
More information? www.nightbalance.com
See backside for more important information and other languages.
Manual
Sleep Position Trainer
EN NL DE FR IT DK
once to switch on the SPT.
2 hours
03 Position training fase
10 +
100 %
03 Position training fase
(night 10+)
Vibrational feedback everytime
you sleep on your back.
for troubleshooting.
03 LED light
Green SPT is ready for use.
Orange Recharge before next use.
Red Check website for troubleshooting:
nightbalance.com/support
04 Close the pocket fl ap.
90º
90º
Pause mode
01 Activate the 20-minute pause
mode by turning the strap 90°
for 5 seconds or by getting up.
press 2x
Number of times on your supine during the past night
Press twice and count the number of white blinks.
1,5 hours
B. Auto-level adjustments
The SPT automatically monitors your
responsiveness to vibrations. The SPT adjusts
the intensity of the vibrations to suit your
responsiveness.
03 Connect the SPT to your computer.
Warning: Before connecting the SPT to the
computer, you must install the software.
90º