Sunx FX-502 Series Instruction Manual

INSTRUCTION MANUAL
Photoelectric Sensor
Thank you very much for purchasing SUNX products. Please read this In-
struction Manual carefully and thoroughly for the correct and optimum use
of this product.
Kindly keep this manual in a convenient place for quick reference.
Never use this product as a sensing device for personnel protection.
In case of using devices for personnel protection, use products which
meet laws and standards, such as OSHA, ANSI or IEC etc., for person-
nel protection applicable in each region or country.
1 PART DESCRIPTION
Sensing output 1
Sensing output 2
selection indicator
selection indicator
(Yellow)
(Yellow)
Sensing output 2
Sensing output 1
operation indicator operation indicator
(Orange) (Orange)
<Description of the operation part>
UP key SET key
•
• Select setting items
contents
2 MOUNTING
How to connect
1. Fit the rear part of the mounting section of the
2. Press down the rear part of the mounting section
front part of the mounting section to the DIN rail.
How to remove
1. Push the controller forward.
2.
Note:
on the rear portion of the mounting section is likely to break.
pletely.
they stops. (Note 1)
tion till it stops.
the beam-receiving inlet.
If they are inserted in reverse, the sensing performance will deteriorate.
3 WIRING
Make sure to connect or disconnect the quick-connection cable (optional)
in the power supply OFF condition.
How to connect
1. Hold the connector of the quick-connection
cable, and align its release lever with the
groove at the top portion of the controller
connector.
2. Insert the connector till a click is felt.
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
ME-FX502 No.0012-66V
WARNING
UP key DOWN key
SET key
MODE indicator: L / D (Yellow)
MODE indicator: CUST (Yellow)
DOWN key MODE key
• Select a mode
• Cancel during setting
• Select setting items
• Select sensing output
1/2 by long pressing
2
1
2
-
Fiber lock
lever
-
Fiber
FD-G4 or FD-FM2, insert the single
Groove
Quick-connection
cable (Optional)
How to remove
1. Press the release lever at the top of the
quick-connection cable connector, and pull
out the connector.
Note: Take care that if the connector is pulled out without pressing the release lever, the re-
lease lever may break. Do not use a quick-connection cable whose release lever has
broken. Furthermore, do not pull by holding the cable, as this can cause a cable-break.
1
2 4
4 INSTALL MORE AMPLIFIER OF SERIES CON-
NECTION TYPE
Make sure that the power supply is OFF while adding or removing the
series connection type.
Make sure to check the allowable ambient temperature since it depends
on the number of the series connection types connected in cascade.
In case 2 or more the series connection types are connected in cas-
cade, make sure to mount them on a DIN rail.
MODE key
between the end plates MS-DIN-E (optional) mounted at the two ends.
imum 11 the series connection types using sub cables can be added to
When connecting 2 or more the series connection types in cascade, use
the sub cable (optional) for the second series connection type onwards.
When connecting the series connection type are not close to each other in parallel,
be sure to mount the end plate MS-DIN-E
PREVENTION FUNCTION
How to cascade
er, and connect the quick-connection
cables.
tional) at both the ends to hold the
1
4.
plates.
How to remove
1. Loosen the screws of the end plates.
one by one.
5 I/O CIRCUIT DIAGRAM
<FX-502>
Terminal No.
-
Internal circuit
<FX-502P>
Terminal No.
Internal circuit
Notes: 1) The quick-connection sub cable does not incorporate +V (brown) and 0V (blue).
The power is supplied from the connector of the main cable.
Terminal No. Terminal name
1 +V
2 Sensing output 1
0V
4
OPTICAL COMMUNICATION
-
Communication
window
End plate MS-DIN-E
MS-DIN-E (op-
(Optional)
End plate
MS-DIN-E
(Optional)
Color code of quick-connection cable
(Brown) +V (Note 1)
(Black) Sensing output 1
(Blue) 0V (Note 1)
Users' circuit
Color code of quick-connection cable
(Brown) +V (Note 1)
(Black) Sensing output 1
(Blue) 0V (Note 1)
Users' circuit
lever
-
-
INTERFERENCE
MOUNTING
Sub cable
(Optional)
Slide
Main cable
(Optional)
Slide
Load
+
12 to 24V DC
±10%
-
+
12 to 24V DC
±10%
Load
-