Using The Silence Feature; Regular Maintenance - First Alert CO710 User Manual

Carbon monoxide alarm
Hide thumbs Also See for CO710:
Table of Contents

Advertisement

N04-3123-000
N043123000A
NOTES:
1. AGENCY APPROVED CLICHÉS, LABELS AND NAMEPLATES – ALL ARTWORK
CHANGES, OR REVISIONS MUST BE APPROVED BY COMPLIANCE
ENGINEERING – AURORA. THERE ARE NO EXCEPTIONS!
2. ELECTRONIC FILES FOR ARTWORKS ARE STORED AND DISTRIBUTED AS
FOLLOWS:

USING THE SILENCE FEATURE

• ONE DISK FOR OUTSIDE VENDOR
• ARENA FILE – AURORA MARKETING DEPARTMENT.
3. THIS APPROVED DOCUMENT IS REQUIRED FOR IQC INSPECTION OF
VENDOR PARTS DELIVERED TO BRK BRANDS, INC. FOR ACCEPTANCE AND
APPROVAL, DELIVERED PARTS MUST MATCH THE RESPECTIVE ARTWORK
DOCUMENTATION.
4. REFER TO N04-3123-000 FOR PACKAGING AND CONSTRUCTION DETAILS.
5.
DATE CODE IS TO BE PERMANENTLY AND LEGIBLY STAMPED ON THE ALARM
IN A CONTRASTING COLOR, MINIMUM HEIGHT IS 3/64TH INCH (1.2 MM) WITH
The Silence Feature is for your convenience only and will not correct
FORMAT "YYYY MMM DD"
a CO problem. Always check your home for a potential problem after
WHERE:
"YYYY" IS THE 4 DIGIT YEAR DESIGNATION,
"MMM" IS THE 3 DIGIT MONTH DESIGNATION
any alarm. Failure to do so can result in injury or death.
(FIRST 3 LETTERS OF THE MONTH), AND
"DD" IS THE 2 DIGIT DAY DESIGNATION
The Silence Feature is intended to temporarily silence your CO Alarm's alarm
horn while you correct the problem—it will not correct a CO problem. While the
alarm is silenced it will continue to monitor the air for CO.
To Activate the Silence Feature: Press and hold the Silence button until the
horn is silent.
Once you activate the Silence Feature: the Silence cycle will last
approximately 4 minutes.
NOTE: After initial 4-minute Silence cycle, the CO Alarm re-evaluates present
CO levels and responds accordingly. If CO levels remain potentially dangerous
-or start rising higher- the horn will start sounding again.
________________________________________________________________________________________________________________________________________
SILENCING THE END OF LIFE SIGNAL
This silence feature can temporarily quiet the End of Life warning "chirp" for 8 hours up to 7 days. You can silence the End of Life warning "chirp" by pressing the
Silence button. The horn will chirp, acknowledging that the End of Life feature has been activated.
________________________________________________________________________________________________________________________________________
TESTING & MAINTENANCE - WEEKLY TESTING
Test the CO Alarm once a week. If the CO Alarm ever fails to test correctly, have it replaced immediately! If the CO Alarm is not working properly, it
cannot alert you to a problem.
DO NOT stand close to the Alarm when the horn is sounding. Exposure at close range may be harmful to your hearing. When testing, step away when
horn starts sounding.
You can test this CO Alarm by pressing the Test button on the Alarm cover until alarm chirps. The alarm horn will sound: 4 beeps, a pause, then 4 beeps. The alarm
sequence should last 5-6 seconds. If the unit does not alarm, make sure it has been activated correctly, and test again. If the unit still does not alarm, replace it
immediately.
DO NOT try fixing the Alarm yourself – this will void your warranty! If the CO Alarm is still not operating properly, and it is still under warranty,
please see "How to Obtain Warranty Service" in the Limited Warranty. Install a new CO Alarm immediately.
NEVER use vehicle exhaust to test your Alarm! Exhaust may cause permanent damage and voids your warranty
________________________________________________________________________________________________________________________________________

REGULAR MAINTENANCE

To keep the CO Alarm in good working order:
Test it every week using the Test button.
Vacuum the CO Alarm cover once a month, using the soft brush attachment. Never use water, cleaners, or solvents, since these may damage the unit. Test the
CO Alarm again after vacuuming.
Please dispose of or recycle the Alarm properly, following any local regulations. Consult your local waste management authority or recycling
organization to find an electronics recycling facility in your area. DO NOT DISPOSE OF ALARM IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
DO NOT spray cleaning chemicals or insect sprays directly on or near the CO Alarm. DO NOT paint over the CO Alarm. Doing so may cause permanent
damage.
Household cleaners, aerosol chemicals, and other contaminants can affect the sensor. When using any of these materials near the CO Alarm, make sure the room is
well ventilated.
PART NUMBER
ELECTRONIC FILE NO.
N04-3123-000
N043123000A
NOTES:
1. AGENCY APPROVED CLICHÉS, LABELS AND NAMEPLATES – ALL ARTWORK
CHANGES, OR REVISIONS MUST BE APPROVED BY COMPLIANCE
ENGINEERING – AURORA. THERE ARE NO EXCEPTIONS!
2. ELECTRONIC FILES FOR ARTWORKS ARE STORED AND DISTRIBUTED AS
FOLLOWS:
USING THE SILENCE FEATURE
• ONE DISK FOR OUTSIDE VENDOR
• ARENA FILE – AURORA MARKETING DEPARTMENT.
3. THIS APPROVED DOCUMENT IS REQUIRED FOR IQC INSPECTION OF
VENDOR PARTS DELIVERED TO BRK BRANDS, INC. FOR ACCEPTANCE AND
APPROVAL, DELIVERED PARTS MUST MATCH THE RESPECTIVE ARTWORK
DOCUMENTATION.
4. REFER TO N04-3123-000 FOR PACKAGING AND CONSTRUCTION DETAILS.
5.
DATE CODE IS TO BE PERMANENTLY AND LEGIBLY STAMPED ON THE ALARM
IN A CONTRASTING COLOR, MINIMUM HEIGHT IS 3/64TH INCH (1.2 MM) WITH
The Silence Feature is for your convenience only and will not correct
FORMAT "YYYY MMM DD"
WHERE:
a CO problem. Always check your home for a potential problem after
"YYYY" IS THE 4 DIGIT YEAR DESIGNATION,
"MMM" IS THE 3 DIGIT MONTH DESIGNATION
any alarm. Failure to do so can result in injury or death.
(FIRST 3 LETTERS OF THE MONTH), AND
"DD" IS THE 2 DIGIT DAY DESIGNATION
The Silence Feature is intended to temporarily silence your CO Alarm's alarm
horn while you correct the problem—it will not correct a CO problem. While the
alarm is silenced it will continue to monitor the air for CO.
While the detector is silenced:
If the CO Alarm...
Is silent for only 4 minutes, then
starts sounding loudly—4 beeps,
pause, 4 beeps, pause
If the CO Alarm...
Remains silent after you pressed
the Silence button
While the detector is silenced:
If the CO Alarm...
Is silent for only 4 minutes, then
starts sounding loudly—4 beeps,
This means...
CO levels are still
potentially dangerous.
This means...
CO levels are dropping.
This means...
CO levels are still
potentially dangerous.
W
C
n
T
B
c
F
D
c
Im
T
A
_
B
B
th
T
d
T
d
w
B
or
lim
or
H
S
th
D
T
is
W
C
n
T
B
c
F

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CO710 and is the answer not in the manual?

Table of Contents