Summary of Contents for K2 Mounts K1-F-S
-
Page 1: Table Of Contents
Table of Contents Before You Begin K1-F-S Installation K1-TS-S & K1-A1-S Installation K2-A1-S Installation K1-UC-S (Under-Cabinet Mount) Installation Specifications K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM... -
Page 2: Before You Begin
Phillips Screwdriver • Electric Drill • 1/8” Drill Bit • 9/16” Wrench (K1-F-S only) • 1/2” Wrench (K2-A1-S only) • 1/4” Drill Bit (K1-UC-S only) To start installation, go to the section pertaining to your specific model. You can find the page number in the Table of Contents. -
Page 3: K1-F-S Installation
K1-F-S Installation Instructions Attach the Screen Plate to the Screen Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. - Page 4 Attach the Wall Plate to the Wall Concrete anchors are not provided. To mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury.
- Page 5 Attach the Screen to the Wall Plate 1. Push the screen plate against 2. Fasten the screw through the wall plate and then let it the screw hole in the bottom slide down into place. of the bracket until it seats against the nut.
-
Page 6: K1-Ts-S & K1-A1-S Installation
K1-TS-S & K1-A1-S Installation Attach the Screen Plate to the Screen Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. - Page 7 Attach the Wall Plate to the Wall Concrete anchors are not provided. To mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury.
- Page 8 Assemble the Arm ( K1-A1-S only) 1. Assemble the arm, and attach it to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...
- Page 9 Attach the Screen to the Wall Plate Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. The K1-TS-S is pictured to the right. The K1-A1-S is pictured on the next page. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...
- Page 10 K1-A1-S Attachment K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...
-
Page 11: K2-A1-S Installation
K2-A1-S Installation Instructions Attach the Screen Plate to the Screen Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. - Page 12 Attach the Wall Plate to the Wall Concrete anchors are not provided. To mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury.
- Page 13 Assemble the Arm 1. Assemble the arm, and attach it to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...
- Page 14 Attach the Screen to the Arm Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...
-
Page 15: K1-Uc-S (Under-Cabinet Mount) Installation
K1-UC-S (Under-Cabinet Mount) Installation Drill the Mounting Holes 1. Remove the contents of your cabinet. 2. Hold the bracket under the cabinet where it will be mounted. 3. Insert a pen or pencil through the mounting holes and make marks where you need to drill. - Page 16 Attach the Front Cap Piece 1. Slide the cap piece onto the bracket as shown. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...
- Page 17 Attach the Mount to the Cabinet 1. Insert four mounting screws down through the holes drilled earlier. 2. Place a spacer on each screw between the cabinet bottom and the top of the mount. 3. Tighten the screws down into the mount holes using the provided hex wrench.
- Page 18 Attach the Screen to the Mount Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen on the screen plate as shown. 2.
-
Page 19: Specifications
Use with products heavier than the maximum weights indicated may result in instability and cause injury. Model VESA Tilt Range Ext. from Wall Max. Load Support Weight K1-F-S 60, 75 360 circle 1.75” 550 lbs 100mm K1-TS-S 60, 75 20° up, 25°down, 60°... - Page 20 K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM...