Advertisement
Quick Links
Advertisement
Summary of Contents for Nasaco NTM1700
- Page 1 2.4GHz Digital Wireless Stereo Amplifier NTM1700 Page 1 Of 15 Rev 00...
-
Page 2: Location Of Functions
Location of Functions A. Transmitter (NTJD800) 1. Power On/Off 2. Power light 3. RCA/LINE IN select switch 4. RSSI light 5. VIDEO/AUDIO select switch 6. LINE IN jack 7. RCA jack 8. Charging jack 9. Power Input Jack Front view Rear view Page 2 Of 15 Rev 00... - Page 3 B. Wireless Stereo Amplifier (NTM1700) Power/RSSI light Left Speaker Output Right Speaker Output Power Input Jack ON/OFF switch Volume knob Front view Page 3 Of 15 Rev 00...
- Page 4 Rear view Accessories: Audio Cable (3.5mm to 3.5mm Stereo) Page 4 Of 15 Rev 00...
- Page 5 RCA to SPK Cable Y Cable (RCA to 3.5 Stereo Plug) Stereo Plug Adaptor (6.3 Plug to 3.5 Jack) Page 5 Of 15 Rev 00...
- Page 6 Adaptor (6V 500mA) for Transmitter EPA-241DAN-15 Adaptor (15V 1600mA) for Wireless stereo Amplifier, Adaptor (15V 800mA) for Wireless Stereo Amplifier Page 6 Of 15 Rev 00...
- Page 7 UL Adapter (Input: 120, 60Hz; Output: 17V, 1.1A), for Wireless Stereo Amplifier, Part no.: HA57U-560 HA57VF-1711, (Input 230Vac 50Hz, 120mA, Output: 17Vdc, 1.1A), for Wireless Stereo Amplifier, Page 7 Of 15 Rev 00...
-
Page 8: Connecting The System
Connecting the System Powering the Transmitter Connect the small, round plug from the transmitter AC power adaptor to the transmitter power input jack and plug the other end of the adaptor into any standard 120V AC wall outlet. Page 8 Of 15 Rev 00... - Page 9 Press the ON/OFF button of the transmitter. The Red LED on the power light should be ON. II. Connecting to an Audio Source Connect the audio cable to the LINE IN jack of the transmitter and plug the other end to audio source (e.g. LINE OUT of DVD player).
- Page 10 The Audio/Video Switch is for latency select. Usually set at Audio for music listening. III. Connecting to Speakers Page 10 Of 15 Rev 00...
- Page 11 Insert bare wire part of speaker cables of to corresponding Left and Right Channel Output of the Wireless Amplifier. IV. Powering the Wireless Amplifier i. Turn the volume by rotating the volume control at the back of the unit to middle. ii.
-
Page 12: Audio Muting
2. If transmitter is found and connected, the power/RSSI indicator will turn green. 3. Turn volume up at the back and you should hear sound coming from the speakers. Adjust the volume as desired. V. Audio Muting When audio source is cut off for 3 minutes, the Wireless Amplifier will be muted. - Page 13 receivers/speakers can maintain its performance and are independent with the no. of receivers in the system. If one “Active” receiver/speaker is powered off, the other “Passive” receivers/speakers cannot be jumped into Active Mode automatically. They have to be powered off first and then power up again to make it “Active”.
- Page 14 Page 14 Of 15 Rev 00...
- Page 15 (1) This device may not cause WITH FCC STANDARDS harmful interference, and (2) this device must accept any interference received, including interference that cause undesired FOR HOME OR OFFICE USE operation. FCC ID LLP-NTM1700 Page 15 Of 15 Rev 00...