Summary of Contents for AMIMON WHDI
- Page 1 WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 Confidential Under NDA Page Internal document. Information subject to change...
- Page 2 Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to AMIMON’s terms and conditions of sale supplied at the time of order acknowledgment.
- Page 3 WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 Contact Us US Office Israeli Headquarters 2350 Mission College Blvd. 2 Maskit St. Suite 500 Building D, 2 Floor Santa Clara, CA 95054 P.O Box 12618 Tel: +1 650 641 7178 Herzlia 46733, Israel...
- Page 4 WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 Version Date Description 25-Sep-07 Initial Release 0.10 17-Oct-07 Updated for SW version App-NXP_0_10: Rx LEDs follow Tx 0.0.19 04-Feb-08 Registration, association, TPC, AFS 0.0.20 13-May-08 Update new TPC 1.0.21 18-Sep-08 Changed from Canary to Pashosh Changed to new application code and new user interface 1.0.22...
- Page 5 (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Amimon for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
-
Page 6: Table Of Contents
WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 1. PURPOSE 2. THE SYSTEM X SIDE 2.1.1 Wireless Tx board 2.1.2 Seagull Interface Tx Board 2.1.3 User Interface board (AMN060) X SIDE 2.2.1 Wireless Rx Board 2.2.2 Seagull Rx Interface Board 2.2.3... -
Page 7: Purpose
WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 1. Purpose This document explains the required steps needed for setting up a link with AMIMON's WHDI Development Platform. This is a basic user's guide that includes troubleshooting and a description of the... -
Page 8: The System
The board also contains the RF components, the Baseband Tx chip and the MAC microprocessor. On the Shaldag board the MAC microprocessor is embedded inside the BB chip. It is connected to the Seagull interface board through a WHDI connector. The wireless board receives its power supply from the Seagull interface board through the WHDI connector. -
Page 9: User Interface Board (Amn060)
Shaldag board the MAC microprocessor is embedded inside the BB chip. It is connected to the Seagull interface board through a WHDI connector. The wireless board gets its 5V power supply from the Seagull interface board through the WHDI connector. -
Page 10: Seagull Rx Interface Board
Stereo I S audio (optional) Optical SPDIF audio input (optional) Seagull board is supporting the following Amimon’s wireless modules (same as fig 1.a): Shaldag (via J15) The board also contains a remote control IR receiver port (optional) that will be supported with later SW versions. -
Page 11: Setting-Up A Link
WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 3. Setting-up a Link 3.1 Enabling communication to the wireless module Seagull boards can work with Shaldag application boards. Canary and Pashosh use I2C protocol with the Seagull board, while Shaldag uses SPI protocol. The Seagull boards contain Dip Switch to select I2C/SPI communication. -
Page 12: System Configuration
4.2 HDMI To ensure full support and optimal performance, the HDMI (or DVI) source and display connected to the WHDI Reference Design system should support EDID and HDCP, and should provide the necessary 5V DC voltage as specified by the HDMI requirements. -
Page 13: User Interface
Tx and Rx can create link only with each other and cannot link with other devices. Note: A system sent from Amimon will already be registered o Button: To start the registration process, apply a long press (3 seconds) on B2 of both Tx and Rx. -
Page 14: Rf Frequencies Table Selection
WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 on B1 when link is already in progress will disassociate. After disassociation the system will automatically try to re-associate. LEDs: L1 is solid yellow once link is established. Figure 5 - User Interface for Association 5.5 RF frequencies table selection... -
Page 15: Manual Frequency Selection
WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 o Button: a short press on B3 will disable TPC and set fixed output power setting. additional press will increment the power according to the following power Steps: 11, 14, 17, 20 & 8 dBm LEDs: LEDs L6, L5 &... -
Page 16: Dvi Mode (Rx Only)
WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 Figure 6 - LEDs for System Error Indication 5.11 DVI mode (Rx Only) In case the display has only a DVI port and the Rx is connected to a display via an HDMI to DVI cable, you should set the Rx in DVI mode which removes the audio from the link. -
Page 17: Basic Troubleshooting
Make sure the HDMI cables used are intact and that you get a good picture by connecting the source directly to the display by an HDMI cable (bypassing the WHDI link). Make sure nothing is touching or blocking the antennas ... - Page 18 WHDI Reference Design Setup Guide Dev Kit-UG1_Rev 1.0.28 Confidential Under NDA Page Internal document. Information subject to change...
Need help?
Do you have a question about the WHDI and is the answer not in the manual?
Questions and answers