Download
Share
Print this page
Technaxx TX-109 User Manual
  1. Manuals
  2. Brands
  3. Technaxx Manuals
  4. Automobile Electronics
  5. TX-109
  6. User manual
Technaxx TX-109 User Manual

Technaxx TX-109 User Manual

Reverse parking assistance with 4 sensors and led display
Hide thumbs

Advertisement

Quick Links

Download this manual
Reverse Parking Assistance with 4 sensors
Suitable for most vehicles as assistance for reverse parking.
This system is designed to be an aid and should NOT replace
Under no circumstances will the manufacturer or supplier
accept any responsibility or can held liable for any direct or
indirect, incidental or consequential damage, or for injuries
resulting from installing or use of this system.
The Declaration of Conformity for this device is under the Internet link:
www.technaxx.de/ (in bottom bar "Konformitätserklärung"). Before using the
device the first time, please read the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks).
Keep this user manual for future reference or product sharing carefully. Do
the same with the original accessories for this product. In case of warranty,
please contact the dealer or the store where you bought this product.
Enjoy your product * Share your experience and opinion on one of the
well-known internet portals such as Amazon or idealo.de
®
Technaxx
& LED display TX-109
the need to drive carefully.
Free Email: support@technaxx.de
* User Manual
Warranty 2 years

Advertisement

loading
Need help?

Need help?

Do you have a question about the TX-109 and is the answer not in the manual?

Questions and answers

Summary of Contents for Technaxx TX-109

  • Page 1 The Declaration of Conformity for this device is under the Internet link: www.technaxx.de/ (in bottom bar “Konformitätserklärung”). Before using the device the first time, please read the user manual carefully. Service phone No. for technical support: 01805 012643 (14 cent/minute from German fixed-line and 42 cent/minute from mobile networks).
  • Page 2 39g / (L) 19.5 x (inner Ø) 22mm (outer one sensor Ø) 25mm / cable length 2.50m Power cable Weight 14.5g / (L) 1.16m Reverse Parking Assistance TX-109, 4x Rear sensors, 1x LED display with Packing Contents sound, Power cable,...

  • Page 3: Wiring Diagram

    Wiring diagram 1 Reverse Gear switch 5 MASS-black 2 Reverse Light 6 Display with sound Supply of Reverse Light 7 Sensors in Bumper +12V Red 4 MASS 8 Control Box...
  • Page 4 INSTALLATION in 4 steps Pre-Installation  Before starting with mounting and removing cover off your car, check to make sure that the vehicle is safely parked and that ALL electrical components are switched OFF. Clean the bumper thoroughly and dry it with clean clothes. Ask a fried or a family member to assist you.
  • Page 5 Diagram 2 & 3 Measure and mark the horizontal position according to diagram 2. The outer most left and most right sensor should ideally be 15m– 20cm away from the edge of the bumper. Locate the Center Line and mark the position of the remaining sensors and according to or to the near approximation of diagram 3.
  • Page 6 2. Preparing to drill  First always check areas behind the bumper to see if it is clear to drill. Attach the small drill bit and push lightly to make a small dent in the bumper in the premarked area and drill all the way through the bumper.
  • Page 7  Mark the sensor plug of each sensor or the end of the cable with the letters A, B, C, D so it is easier to attach them in the right order to the Control Box.  Using a steel wire, tied the sensors cables to one end and guide the other end through into the opening at the underside of the vehicle until you can see it protrude inside the trunk compartment.
  • Page 8 Wire Connection  Follow the connection diagram of the control box. 1 Control Box Sensor D 2 – Black to Ground Sensor C 3 + Red to Reverse light Sensor B 4 Display with sound Sensor A  Attach the black cable of the power cable to the car’s ground (negative) or the negative of the reverse light.
  • Page 9 Sensor testing  Turn on the ignition so the car is under power (differs by the model and the age of your car). DO NOT start the engine.  Make your handbrake on. Then shift the gear to reverse.  Place the display for testing in the trunk. ...

  • Page 10: Special Note

     Repeat this process for all remaining sensors, one at a time. Once you are satisfied that everything is working, plug all sensors to their corresponding slot in the Control Box. Do a final check to ensure that everything is correctly plug into its right position.
  • Page 11 B will be detected sooner or later, but A may not be detected at all. Spherical objects have a small and uneven surface area, due to the curvature of spherical object the signal reflected away, maybe. Cliff or Water edges where there are no objects directly behind, will not be detected.
  • Page 12 Cleaning: Protect device from contamination and pollution (use a clean drapery). Avoid using rough, coarse-grained materials or solvents/aggressive cleaner. Wipe the cleaned device accurately. Distributor: Technaxx Deutschland GmbH & Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany...