Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for eastern WL-1000
-
Page 2: Table Of Contents
................... Important safety instruction ............................Feature ..........................Structure ..............Index to part & control [WL-T1000 Receiver] ..........................Front Panel ..........................Back Panel ..............Index to part & control [WL-R1000 Receiver] ..........................Front Panel ..........................Back Panel ................... Function of Remote control ........................ - Page 3 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Page 4: Important Safety Instruction
FCC Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. -
Page 5: Feature
AFHSS (Adaptive Frequency Hopping Spread Spectrum) When there is an error or interference during sending data on a channel, which is changed to another channel immediately then this is very strong method to microwave or wireless LAN. (Forward Error Correction) When there is an error or interference during sending data, this system change data immediately so that people do not notice any mistake during correction. -
Page 6: Index To Part & Control [Wl-T1000 Receiver]
Front Panel AUTO LED This set is to Auto channel set-up. SLEEP LED If there is no signal input over 3 minute or no power on player connecting to Transmitter, sleep mode is operating then SLEEP LED turns up. STAND BY / VOLUME REMOTE CENSOR INPUT SELECT... -
Page 7: Index To Part & Control [Wl-R1000 Receiver]
Front Panel VOLUME Back Panel SPEAKER FILTER LINE OUT RESET SPEAKER OUTPUT Set speaker filter ' I ' for connecting 4 ohm speaker Set speaker filter ' Il ' for connecting 8 ohm speaker... -
Page 8: Function Of Remote Control
Function of remote STAND BY L /ON INPUT L /OFF STAND BY: Stand by on / off MANUAL AUTO STAND BY VOLUME INPUT: input select L /ON INPUT L /OFF L/OFF: Antenna lamp off L/ON: Antenna lamp on MANUAL AUTO AUTO: Auto channel set up MANUAL / CH.: Fixed channel set up VOLUME... -
Page 9: Connecting
NOTE The distance of Tx and Rx for best performance is 4m to 6m. The position of Tx and Rx for best performance is the same height and the same line. No hindrance between Tx and Rx makes you the best performance. The socket-outlet shall be installed near the equipment and shall be easily accessible. -
Page 10: Connecting Transmitter [Wl-T1000]
Connecting DVD Player built decoder in. 1. Connect DC 9V adapter to DC input jack on the back of WL-T1000. 2. Plug in DC 9V adapter connecting WL-T1000. 3. Connect LOW-INPUT to surround out jack of DVD player. OUT-PUT CEN. WOO. -
Page 11: Connecting 5.1Ch Sound Card
1. Connect DC 9V adapter to DC input jack on the back of WL-T1000. 2. Plug in DC 9V adapter connecting WL-T1000. 3. Connect LOW-INPUT to rear jack of computer FRONT OUT L / R REAR OUT L / R SUB WOOFER CENTER SPEAKER OUT PUT... -
Page 12: Connecting Receiver [Wl-R1000]
1. Plug in the power cord of receiver [WL-T1000] 2. Connect surround speaker to receiver 3. Select speaker impedance using speaker filter switch. ( 'I' or 'II' ) I : ON 4. Set up power switch on right side of receiver 'I'. O : OFF Surround Surround... -
Page 13: Basic Operation
POWER ON Back panel of Transmitter (WL-T1000) Right side of Receiver (WL-R1000) 1. Connect DC 9V adapter to DC input jack on the back of WL-T1000 2. Switch on WL-T1000. 3. Plug in WL-R1000. 4. Switch on WL-R1000 Power Blue LAMP of WL-T1000 and WL-R1000 flicker, which means STAND-BY. (AUTO ID Pairing) NOTE Do not use the power switch on WL-T1000 and WL-R1000 if possible. -
Page 14: Selecting Input
VOLUME 2. Press test tone of DVD receiver or 5.1ch amplifier. 3. Adjust volume level of WL-1000 to match the other channels from test tone. Use test tone of DVD player if your 5.1ch amplifier does not have any decoder. -
Page 15: Selecting Auto Channel
AUTO Lighting OFF continuously 2. Press L/OFF button on the remote control Whenever pressing button of remote or WL-1000, LAMP is light on for approximately 10sec. Light off LAMP if possible as audio drop out is affected by LED. NOTE... -
Page 16: Specifications
Transmitter [WL-T1000] Receiver [WL-R1000]...