Download
Share
Print this page
Poulan Pro PR174Y22RHPE Operator's Manual
  1. Manuals
  2. Brands
  3. Poulan Pro Manuals
  4. Lawn Mower
  5. PR174Y22RHPE
  6. Operator's manual
Poulan Pro PR174Y22RHPE Operator's Manual

Poulan Pro PR174Y22RHPE Operator's Manual

Hide thumbs

Advertisement

Quick Links

PR174Y22RHPE
EN
Operator's manual
2-14

Advertisement

loading
Need help?

Need help?

Do you have a question about the PR174Y22RHPE and is the answer not in the manual?

Questions and answers

Related Manuals for Poulan Pro PR174Y22RHPE

Summary of Contents for Poulan Pro PR174Y22RHPE

  • Page 1 PR174Y22RHPE Operator's manual 2-14...

  • Page 2: Table Of Contents

    Contents INTRODUCTION............2 MAINTENANCE............10 SAFETY..............4 TRANSPORTATION AND STORAGE....13 ASSEMBLY...............6 TECHNICAL DATA..........14 OPERATION.............8 INTRODUCTION Operator's manual 1-800-805-5523 (Canada) 8:00 AM to 7:00 PM EST The initial language of this operator's manual is English. Operator's manuals in other languages are translations from English.
  • Page 3 Symbols on the product not start the engine indoors or in closed spaces. Warning Hot surface Read this manual Always stop the engine before refueling. Wear approved hearing protection. Keep hands and feet away from rotating blades. Fuel Keep hands and feet away from rotating blades.

  • Page 4: Safety

    SAFETY Safety definitions and can contain a spark which can start a fire. Not sufficient airflow can cause injury or death The definitions below give the level of severity for because of asphyxiation or carbon monoxide. each signal word. • When you use this product the engine makes an electromagnetic field.
  • Page 5 • Do not operate the product in wet grass. • Do not cut on wet grass. You can fall. • Be careful near corners, bushes, trees or other • Do not cut on terrain with more than a 15 degree objects that can prevent your view.

  • Page 6: Assembly

    Rear deflector and rear door product. Always use accessories that are approved by the manufacturer. The rear deflector and rear door decrease the risk of • If the maintenance is not done correctly and objects being ejected from behind the product into regularly, the risk of injury and damage to the the operator’s mow position.
  • Page 7 3. Remove all package materials. 4. Remove the product from the carton and make sure no loose parts are left in the carton. To set the product in operation position To install the starter rope handle 1. Lift the lower handle section to operation position.

  • Page 8: Operation

    To set the cutting height 1. Squeeze the height adjuster lever in the direction of the wheel. The cutting height can be adjusted to 9 (1-9) 2. Move the wheel up or down for your cutting different positions. Lift the wheels for a low cut and requirements.
  • Page 9 To do an electric start on the product 4. Keep the charger connected for a minimum of 6 hours before you start the engine with an electric 1. Go behind the machine. starter. 2. Hold the operator presence control bar down to 5.

  • Page 10: Maintenance

    2. Remove grass clippings from the grass catcher from below the handle. 3. Empty grass clippings from the bag with the frame handle and the bag handle. MAINTENANCE WARNING: Read and understand the safety chapter before you clean, repair or do maintenance on the product. Maintenance schedule Use the maintenance schedule to see the necessary Note: If more than one time interval is identified in...
  • Page 11 To change the oil Note 3: Charge the battery for max. 48 hours. To do a general inspection Maintenance schedule on page 10 for more information about when to change the oil. • Check that nuts and screws are tight. 1.
  • Page 12 To clean the product To replace the side discharge deflector • Brush off leaves and grass. • Keep finished surfaces and wheels free of The side discharge deflector is attached to the side gasoline, oil and unwanted material. discharge opening of the product. It decreases the •...

  • Page 13: Transportation And Storage

    • Always make sure that the blade is correctly 5. Examine the motor shaft to make sure that it is ground and balanced. To examine the blade not bent. balance, use a 5/8 in (16 mm) diameter steel 6. When you attach the new blade, point the angled bolt, pin or a cone balancer.

  • Page 14: Technical Data

    TECHNICAL DATA Product specifications Gasoline capacity and type Unleaded regular (maximum 10% ethanol) • SAE 30 (above 0°C (32°F) Oil type (API: SG-SL) • SAE 10W30 (above 0°C (32°F) • SAE 5W30 (below 0°C (32°F) Oil capacity See the engine manufacturer's manual for more information. Spark plug See the engine manufacturer's manual for more information.
  • Page 15 438 - 001 - 29.11.2017...
  • Page 16 www.poulanpro.com Original instructions 115958927 2017-12-04...
Save PDF