Advertisement

SAILOR H1252A/TT-3608A-220 Printer
SAILOR H1252B/TT-3608A Printer
Technical manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SAILOR H1252A/TT-3608A-220 and is the answer not in the manual?

Questions and answers

Alex
March 19, 2025

Hi, i wanted to know about replacing and installing ink for this printer. I cant see how to do this or where to purchase a new ink roller. Ours is becoming light.

Subscribe to Our Youtube Channel

Summary of Contents for COBHAM SAILOR H1252A/TT-3608A-220

  • Page 1 SAILOR H1252A/TT-3608A-220 Printer SAILOR H1252B/TT-3608A Printer Technical manual...
  • Page 3 SAILOR H1252A/TT-3608A - 220 Printer SAILOR H1252B/TT-3608A Printer User manual Document number: 98-124013-B Release Date: 20 December 2013...
  • Page 4 Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this infor- mation should acquire the most current version e.g. from cobham.com/satcom or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.
  • Page 5: Table Of Contents

    PART I Contents PART I H1252A / TT-3608A-220 H1252B / TT-3608A 1 General information ........................2 2 Installation ............................3 Mounting possibilities ......................3 PART II H1252B / TT-3608A 1 General information .........................6 Introduction ..........................6 Principle of operation ......................6 Technical data .........................6 2 Maintenance/modification ....................7 Disassembling to remove the mains transformer ..........7 Disassembling and mounting of the ON-OFF switch ...........8 Mounting the DC power supply and reassembling ..........8...
  • Page 6: General Information

    PART 1 General information H1252A/TT-3608A-220 Hardcopy printer is an OKI MICROLINE 182/280 printer for 220/240V AC operation. H1252B/TT-3608A Hardcopy printer is an OKI MICROLINE 182/280 printer with built-in DC power supply for 10.5-32V DC operation. The printer is as standard delivered with a Roll Paper Stand, other paper types can also be used, please refer to the OKI manual for detailed information.
  • Page 7: Installation

    PART I Installation Mounting possibilities Mounting kit H1250 280 mm 371 mm 28709 Drilling plan 4 pcs ø6 mm 300 mm 341 mm 28711 0627...
  • Page 8 PART 1 Mounting kit H2192 442 mm 325 mm 28699 Drilling plan 2 pcs 4 mm 428 mm 442 mm 28710 0627...
  • Page 9 PART II Printer with mounting kit H1250 Self-cutting screws, 4 pieces 4.2 x 25 Washers, 4 pieces M4 Screws, 3 pieces M4 x 20 28641A Printer with mounting kit H2192 Self-cutting screws, 2 pieces 4.2 x 25 Washers, 2 pieces M4 Screws, 3 pieces M4 x 20 28697 0627...
  • Page 10: General Information

    PART II General information Introduction This section gives you all the necessary informations to maintaine the DC power sup- ply module. It also specify how to modify the printer to operate on DC supply instead of AC supply. Principle of operation The power supply module is constructed to operate from a battery voltage of 10.5V DC to 32V DC to deliver the necessary voltages for the printer.
  • Page 11: Maintenance/Modification

    PART II Maintenance/modification This section is intended for use when modifying the printer to operate from DC supply instead of 220V AC supply. Disassembling to remove the mains transformer Remove the access cover by lifting up rear edge. Pull out the platen knob. Remove the two screws.
  • Page 12: Disassembling And Mounting Of The On-Off Switch

    PART II Disassembling and mounting of the ON-OFF switch It is necessary to remove the ON-OFF switch from the transformer assembly to use it again on the DC power supply module. Remove the filter and switch board from the transformer by pulling it off. Unsolder the ON-OFF Switch. Solder the switch to the two loose wires on the DC power supply module. Then twist the wires to the switch to suppress noise.
  • Page 13: Mounting Of The Dc Power Supply

    PART II DC power supply circuit board is fixed to the mounting frame with four screws The ON-OFF Switch is placed in the printer panel cutout and fixed to the PCB with a glue pad 28557 Note: Remove the " 220V ~ " label 2.3.1 Mounting of the DC power supply Place the ground connection over the rear transformer hole, and fix it with the ground screw.
  • Page 14: Reassembling Of The Printer

    PART II Run the printer selftest programme. Switch on the ON-OFF switch and simultaneously press down the “line feed” button. After a few seconds (at low input voltage) the printer starts the selftest printing routine, which means that the DC power supply is OK. Switch off the printer. (D10) Main Control Board 28479 2.3.3 Reassembling of the printer Place the top cover by lifting the front end and place holes in the rear end into the two...
  • Page 15: Electrical Connections

    PART II Electrical connections ON-OFF SWITCH FROM MAINS TRANSFORMER OUTPUT CABLE GREEN BLACK BLACK YELLOW/GREEN DC INPUT CABLE 28558 0627...
  • Page 16: Service

    PART II Service Printer selftest To do a performance test of the DC power supply, a selftest programme in the printer can be used. Connect a DC power source of 10.5V to 32V to the DC input connector. Switch on the ON-OFF switch and simultaneously press down the “line feed” button. After a few seconds (at low input voltage) the printer starts the selftest a printing routine, which means that the power supply is OK.
  • Page 17: Mechanical Disassembling Of Printer

    PART II Mechanical disassembling of printer 28560 0627...
  • Page 18: Circuit Description

    PART II Circuit description DC power supply To suppress noise on the supply wires a filter is build around the current compensated choke L1. Furthermore the RC snubbers across the transformer prevent unwanted oscil- lations during transition time. The diode D7 in conjunction with R16 and C19 clamps the transient voltage spikes across the switch transistor Q1. When the supply is switched on, the capacitor C6 is charged by means of R1 and when the voltage exceeds approx.
  • Page 19 PART II Component location DC power supply View from component side with upper side tracks. View from component side with lower side tracks. PCB rev. 28471C 0627...
  • Page 20 PART II Schematic diagram DC power supply This diagram is valid for PCB rev.28471C...
  • Page 22 98-124013-THR-B www.cobham.com/satcom...

This manual is also suitable for:

Sailor h1252b/tt-3608a

Table of Contents

Save PDF